Q-Logic 8200 SERIES manual Accessing the CLI, To telnet to the CLI from a web browser

Page 84

B – Command Reference Accessing the CLI

Q

B.2

Accessing the CLI

Once the management port (labeled on the port side of SANbox SSP) has been properly configured with an IP address, a user can telnet to the SANbox SSP using a web browser or standard telnet application. After successful bootup, the management port is available for management purposes.

See "To modify Ethernet settings for remote access:" on page 3-8or "Modify Eth Command" (page B-13), if you did not already configure the management port for remote access.

NOTE: To gain access to the CLI, type the default login and password.

login: kadmin

password: kahuna

To telnet to the CLI from a web browser:

1.In your web browser, type the IP address of SANbox SSP (example: http://10.4.2.123).

The following screen displays (see Figure B-1):

NOTE: The version number of the SANbox SSP is listed next to the Version label at the top of the screen.

Figure B-1. QLogic SANbox Storage Services Platform (SSP) Screen

B-4	SN0054628-00 A

Image 84

Contents SANbox 8200 Series Storage Services Platform Page Table of Contents Using the SANbox SSP Section SANbox SSP Management GUI ReferenceSection Troubleshooting Figures Tables Page Introduction Audience Readme FileRelated Documentation Style Conventions Regulatory and Safety Notices New in this ReleaseDeclaration of Conformity ManufacturerProduct Introduction Regulatory and Safety Notices Warranty and Technical Support Before Contacting Technical SupportAvailability TrainingContact Information Introduction Warranty and Technical Support SN0054628-00 a SANbox SSP and StoreAge Solution Overview General DescriptionSANbox SSP/StoreAge Solution Features SANbox SSP OverviewSupported Network Configurations Small SAN Deployment Configuration with ZoningSmall SAN Configuration with Front/Back-Side SANs Dual Fabric ConfigurationHigh-Availability Configuration High-Availability Fabric Configuration How the Solution Protects Against Failures Setup RequirementsPort Connections Fibre Channel Port Connections Ethernet ConnectionsConsole Port Connection General Description Port Connections SN0054628-00 a Roadmap of Setup Tasks Task RoadmapChecking Package Contents Setting Up SANbox SSP SANbox 8200/8202 SSP Port SideSetting Up SANbox SSP Hardware SANbox 8200/8202 SSP Fan SideTo install the power supplies To mount SANbox SSP in a rackInserting the Right Power Supply To connect the console portAccessing SANbox SSP for the First Time To power up SANbox SSPTo configure the terminal settings on the host computer To access the CLI through the serial console portTo modify Ethernet settings for remote access Gateway NetmaskConnecting to the SAN Connecting StoreAge SVM Appliances to the SANConnecting SANbox SSPs to the SAN To connect SANbox SSPs to the SANConnecting Hosts to the SAN Managing your ConfigurationTo connect hosts to the SAN Page SANbox SSP Management GUI Reference Managing SANbox SSPUsing the SANbox SSP Management GUI To install Java WebStartQLogic SANbox Storage Services Platform SSP Screen SANbox SSP Management GUI Application Installation Screen To log into the SANbox SSP Management GUIUsing the Command Line Interface Remotely Using the Command Line Interface LocallyTo access the CLI using telnet To access the CLI using sshNavigating the SANbox SSP Management GUI SANbox SSP Management GUI FunctionsSystem To manage external port behaviorEnabling and Disabling Ports Ethernet Panel System System Ethernet PanelSensors Panel System System Sensors PanelDiagnostics To use the Diagnostics panelTelnet Telnet Screen Initiated from the SANbox SSP Management GUI10. Diagnostic Screen Log Panel LogPage Using the SANbox SSP Setting up a High-Availability ConfigurationComponent SAN Zoning High-Availability Fabric Configuration with Zoning Directly Connecting Devices to SANbox SSP Yellow zone Pink zoneConfiguring Storage AccessZoning Configuration Restriction on RAID Devices Maximum Frame SizeUsing the SVM GUI to Manage Virtual Storage To create storage poolsTo create virtual volumes Guidelines for Selecting the Storage Device ProfileFailing Back Click Fail BackTo shut down SANbox SSP using the Main Power Switch Shutting Down SANbox SSPTo restart SANbox SSP from the CLI To shut down SANbox SSP from the CLIUsing the SANbox SSP Shutting Down SANbox SSP SN0054628-00 a Maintaining the SANbox SSP SANbox SSP System SoftwareBoot Sets To select the active boot set from the local consoleMaintenance Mode To access Maintenance Mode from the local consoleTo install a new system software image on SANbox SSP Updating SANbox SSP System SoftwareTo apply a system software patch To install a new Maintenance Mode image on SANbox SSP Interpreting the LED PatternsTo replace the power supplies Post and the LEDsReplacing Hardware Components To replace the fansAbout the Transceivers To replace a transceiverPage Troubleshooting Before Looking at the Problem StatementsProblem Statements and Troubleshooting Procedures BACK-END Storage not Found LOOP/FABRICCannot Access SANbox SSP Console Port Cannot LOG Into SANbox SSP GUI or CLIInitiator not Found by SVM Performance Characteristics MediaHigh Availability Features Storage ManagementStandards Device Management MechanicalEnvironmental ElectricalRegulatory Command Line Interface CLI Overview Command Quick Reference by ObjectTable B-1. Commands by Object Type Command Syntax and Command Completion Help Commands Online HelpExample Accessing the CLI To telnet to the CLI from a web browserFigure B-2. Telnet Console Login Screen Users and Groups Figure B-3. Telnet Console Menu OptionsTable B-2. Built-In Users and Groups Commands Clear Command Create User CommandDelete User Command Group group nameDisable Eth Command Disable Port CommandDisable eth ethernet name Disable portDisable snmpv3 Command Disable User CommandEnable Eth Command Syntax disable snmpv3Enable Port Command Enable snmpv3 CommandEnable User Command Exit Command Help CommandKeywords help partial command name Help Commands Modify Date CommandModify Eth Command Modify Port Command Capability port capabilitySpeed port speed Type port typeModify Ports Command Maxframesize size in bytesPorts type port type Modify Timezone Command Modify User CommandPassword Speed port speed NEGOTIATE, 1G, 2GQuit Command Reboot CommandReset Port Command Reset portRestart snmp Command Set Community CommandShow Chassis Command Show Community Command Show Date CommandShow Debug Command SerialnumDump FcptstateFcsexch FcslunsShow Eth Command Show Eths Command Show Fan CommandShow eths Show fanShow Fans Command Show Group CommandShow Groups Command Show ID CommandShow Ports Command Keywords show port port numberShow ports Show ps Command Keywords show ps power supply number Show psShow ps Show pss Command Show snmpv3 CommandShow Status Command Show Therm CommandShow Therms Command Show Timezone CommandShow User Command Show Users CommandShow Voltage Command Show Voltages CommandVersion Command Active Boot Set Boot SetDefault Boot Set Active/Active RAIDInactive Boot Set Invalid Boot SetMaintenance Mode Image FailoverValid Boot Set Scsi PersonalitySecondary Path Storage PoolVirtual Volume Virtual DiskIndex LEDs 3-10,6-5 SN0054628-00 a Index-3 SVM GUI SN0054628-00 a Index-5