Pelco FR82011 manual Important Safety Instructions

Page 4

Important Safety Instructions

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14.Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases shall be placed on the apparatus.

15.WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

16.Installation should be done only by qualified personnel and conform to all local codes.

17.Use only installation methods and materials capable of supporting four times the maximum specified load.

18.A CCC-approved power cord must be used to power this equipment when used in China.

19.CAUTION: These servicing instructions are for use by qualified service personnel only.

To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

4

C2653M (6/07)

Image 4
Contents FT82011/FR82011 Ethernet Media Converter Page List of Illustrations ContentsList of Tables Important Safety Instructions Risk of Electric Shock Do not Open Regulatory Notices Radio and Television InterferenceProduct Overview DescriptionC2653M 6/07 Models Multimode ModelsSingle-Mode Models*† RK5000PS-5U rack mount chassisFront Panel 10BASE-T/100BASE-TX Ports 1-4, RJ-45 connectors Rear PanelInstallation Package ContentsFlow control default setting 10BASE-T/100BASE-TX Modes of OperationMounting Mounting the FT82011/FR82011 Module Into a RackMounting the FT82011/FR82011 Module Using the Wall Clip Connections Fiber connection Troubleshooting Optic Fault LED Color MeaningAny of the following fault conditions If the cable is Receive optical signalCheck for problems Budget specification statedMeaning Possible Cause Corrective Action Optic Fault LED Laser has reached end of lifeTable C. Troubleshooting with Rear-Panel Indicators Lished Is not desired, refer to the SettingAmber Amber Is occurringMeaning Possible Cause Not litDesired, no action is required. If Full-duplexMode Occur on a half-duplex link Required Half-duplexMode Not desired, refer to the Setting Color Meaning Possible Cause Corrective ActionDesired, no action is required Or if it is not the proper cableNot lit Quality of Service SpecificationsWeighted fair queuing scheduling Model Number Wavelength Optical Maximum Transmit/Receive ReceiverEnd Multimode 62.5/125 μmAppendix. RJ-45 Connector Pinouts Not usedC2653M 6/07 Product Warranty and Return Information ISO9001