Pelco FR82011 manual Product Overview, Description

Page 7

Product Overview

DESCRIPTION

The FT82011/FR82011 Ethernet media converter converts 10BASE-T/100BASE-TX data to 100BASE-FX data and vice versa. Designed for point-to-point applications, the FT82011/FR82011 media converter provides one 10BASE-T/100BASE-TX port and one 100BASE-FX fiber port. The FT82011 and FR82011 media converters are used in combination with one another to provide wavelength compatibility. Using wavelength division multiplexing (WDM), bidirectional data is transported in a single fiber (refer to Figure 1).

ONE 10/100 Mbps

 

ONE 10/100 Mbps

CONNECTION

 

 

CONNECTION

 

FT82011

 

FR82011

 

 

 

ONE

 

 

 

 

FIBER

 

 

Figure 1. FT82011 and FR82011 Point-to-Point Application

Features of the FT82011/FR82011 Ethernet media converter include the following:

•User-selectable 10BASE-T/100BASE-TX port functions:

–Autonegotiation between 10 Mbps and 100 Mbps data rates and between full-duplex and half-duplex modes

–10 Mbps or 100 Mbps selectable

–Full-duplex or half-duplex mode selectable

–Enabling/disabling of flow control

NOTE: The 100BASE-FX fiber port is automatically forced to full-duplex 100 Mbps operation.

•Auto MDI/MDI-X (Medium Dependent Interface/Medium Dependent Interface Crossover) operation

•Link-down detection, which propagates a link-down status among all 10BASE-T/100BASE-TX and 100BASE-FX ports connected in the network when a 10BASE-T/100BASE-TX link or 100BASE-FX link goes down. As a result, all ports are disabled and data transmission halts until the faulty link is restored.

•Compliant with IEEE 802.3, 802.3u, 802.3x standards

•Multimode fiber support for distances up to 2 km

•Single-mode fiber support for distances up to 46 km

•Laser diode for transmission of optical signals

NOTE: The FT82011/FR82011 media converter is a Class 1 laser product that complies with FDA radiation performance standard 21CFR Subchapter J and with IEC 60825-1 Edition 1.2, 2001-08.

C2653M (6/07)

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents FT82011/FR82011 Ethernet Media Converter Page List of Illustrations ContentsList of Tables Important Safety Instructions Risk of Electric Shock Do not Open Radio and Television Interference Regulatory NoticesDescription Product OverviewC2653M 6/07 RK5000PS-5U rack mount chassis ModelsMultimode Models Single-Mode Models*†Front Panel Rear Panel 10BASE-T/100BASE-TX Ports 1-4, RJ-45 connectorsPackage Contents Installation10BASE-T/100BASE-TX Modes of Operation Flow control default settingMounting the FT82011/FR82011 Module Into a Rack MountingMounting the FT82011/FR82011 Module Using the Wall Clip Connections Fiber connection Troubleshooting Color Meaning Optic Fault LEDBudget specification stated Any of the following fault conditions If the cable isReceive optical signal Check for problemsLaser has reached end of life Meaning Possible Cause Corrective Action Optic Fault LEDAmber Is occurring Table C. Troubleshooting with Rear-Panel IndicatorsLished Is not desired, refer to the Setting AmberNot lit Meaning Possible CauseOccur on a half-duplex link Required Half-duplex Desired, no action is required. IfFull-duplex ModeOr if it is not the proper cable Mode Not desired, refer to the SettingColor Meaning Possible Cause Corrective Action Desired, no action is requiredNot lit Quality of Service SpecificationsWeighted fair queuing scheduling Multimode 62.5/125 μm Model Number Wavelength Optical Maximum Transmit/ReceiveReceiver EndNot used Appendix. RJ-45 Connector PinoutsC2653M 6/07 Product Warranty and Return Information ISO9001
Top Page Image Contents