Sun Microsystems CP3000 manual Obtain the AMC card from the ship kit, 5Sample Top View

Page 24

3. Obtain the AMC card from the ship kit.

Note – Be sure to follow unpacking and handling instructions. See Section 1.2, “Unpacking” on page 1-3and Section 1.3, “Handling AMCs” on page 1-4.

FIGURE 1-5Sample Top View

Note – The illustration shows a sample of the top view for a 146GB AMC. If your AMC has a different capacity, the label shows it.

4.Perform any card-specific hardware procedures, if necessary.

5.Prepare the AMC by fully opening its injector/ejector latches to the OUT position.

1-14Sun Netra CP3000 Advanced Mezzanine Card PCIe Hard Drive and SAS Controller User’s Guide • March 2010

Image 24
Contents For the AMC.1-HDD SAS Disk Please Recycle Contents Overview Managing the AMCConfiguring the AMC Connectors and PortsEnvironment Specifications Agency CertificationsIndex Index-1 Preface Typographic ConventionsRelated Documentation Third-Party Web SitesSun Welcomes Your Comments Page Important Safety Information for Sun Hardware Systems Getting StartedSystem Requirements Operating Systems CompatibilityChassis Compatibility Blade Server CompatibilityUnpacking Electrical and EnvironmentalHandling AMCs AMC Faceplate 1AMC.1-HDD SAS Disk FaceplateAMC LEDs 1AMC Status LEDs2Hot-Swap Blue LED States Removing and Installing AMCs Removing an AMCShut down the payload OS Hot-Swap LED starts blinking 2Deactivating the AMC Remove the AMC 3Removing the AMCRemoving a Blade Server and AMC 4Front Cable Management Bracket in Lower PositionInstalling an AMC Remove the filler panel, if necessaryObtain the AMC card from the ship kit 5Sample Top View6Opening the Injector/Ejector Latch Page Push the ejector latch in fully 7Inserting the AMC Into a Blade ServerTo Enable AMC Port 2 Driven by Port 1 of SAS Controller To Enable AMC Port 3 Driven by Port 2 of SAS ControllerPower on the system, if necessary Enabling and Disabling SAS PortsTo Disable AMC Port 2 Driven by Port 1 of SAS Controller To Disable AMC Port 3 Driven by Port 2 of SAS ControllerPage Overview Features Power Regulator Key ComponentsHard Drive Disk SAS Controller FlashModule Management Controller MMC Port Connectors Faceplate and LEDsLEDs OOS Functional Diagram Technical Support and WarrantyPage 4Sun Netra CP3000 AMC.1-HDD SAS disk Barcode Labeling Disposal Managing the AMC Supported Ipmi Commands Monitoring and Control FunctionsIpmi Controller 1Supported Ipmi Commands FRU Information 2Standard FRU Data RecordsSensors 3Threshold SensorsFirmware and Software Upgrades Readme files within the download packageConfiguring the AMC Configuration Tools Boot Bios UtilityFeatures and Configurations Launching the Boot Bios UtilityPress Ctrl C Page OpenBoot Bios 2Adapter Properties MenuExtensible Firmware Interface EFI Enabling and Disabling Channel PortsConnectors and Ports Connector Locations and Assignments Connector PinoutsTable A-1Pin Assignments Appendix a Connectors and Ports SAS Controller Ports Keying Ports 1AMC e-Keying Port AssignmentsPage Environment Specifications Table B-1Electrical Specifications Table B-2Environmental SpecificationsElectrical and Environmental ElectricalTable B-3MTBF Values by Temperature RPMReliability Absolute Maximum RatingsNormal Operating Ranges Board Dimensions and Weight AMC.1-HDD SAS disk PCB DimensionsMechanical Page Agency Certifications CE Certification NEBS/ETSISafety Emissions Test Regulations 1 EN 55022 Emissions2 EN 55024 Immunity Regulatory Information FCC USAIndustry Canada Canada Page Index NumericsNEBS/ETSI, C-2