Sun Microsystems CP3000 Extensible Firmware Interface EFI, Enabling and Disabling Channel Ports

Page 52

4.4Extensible Firmware Interface (EFI)

BIOS

The AMC.1-HDD SAS disk includes an EFI boot services driver for use with ATCA blades that feature Intel® IA64 processors. Additional information is available at http://www.lsi.com.

4.5Enabling and Disabling Channel Ports

As shipped from the factory, the AMC.1-HDD SAS disk will not drive AMC channel ports, due to the default “disable” setting. You can enable these ports using lsiutil, a command line utility. For instructions, see Section 1.7, “Enabling and Disabling SAS Ports” on page 1-18.

4-6Sun Netra CP3000 Advanced Mezzanine Card PCIe Hard Drive and SAS Controller User’s Guide • March 2010

Page 51 Page 53
Image 52
Page 51 Page 53
Contents For the AMC.1-HDD SAS Disk Please Recycle Contents Overview Managing the AMCConfiguring the AMC Connectors and PortsEnvironment Specifications Agency CertificationsIndex Index-1 Preface Typographic ConventionsRelated Documentation Third-Party Web SitesSun Welcomes Your Comments Page Important Safety Information for Sun Hardware Systems Getting StartedSystem Requirements Operating Systems CompatibilityChassis Compatibility Blade Server CompatibilityUnpacking Electrical and EnvironmentalHandling AMCs AMC Faceplate 1AMC.1-HDD SAS Disk FaceplateAMC LEDs 1AMC Status LEDs2Hot-Swap Blue LED States Removing an AMC Removing and Installing AMCsShut down the payload OS Hot-Swap LED starts blinking 2Deactivating the AMC Remove the AMC 3Removing the AMCRemoving a Blade Server and AMC 4Front Cable Management Bracket in Lower PositionInstalling an AMC Remove the filler panel, if necessaryObtain the AMC card from the ship kit 5Sample Top View6Opening the Injector/Ejector Latch Page Push the ejector latch in fully 7Inserting the AMC Into a Blade ServerTo Enable AMC Port 2 Driven by Port 1 of SAS Controller To Enable AMC Port 3 Driven by Port 2 of SAS ControllerPower on the system, if necessary Enabling and Disabling SAS PortsTo Disable AMC Port 2 Driven by Port 1 of SAS Controller To Disable AMC Port 3 Driven by Port 2 of SAS ControllerPage Overview Features Key Components Power RegulatorHard Drive Disk Flash SAS ControllerModule Management Controller MMC Faceplate and LEDs Port ConnectorsLEDs OOS Functional Diagram Technical Support and WarrantyPage 4Sun Netra CP3000 AMC.1-HDD SAS disk Barcode Labeling Disposal Managing the AMC Monitoring and Control Functions Supported Ipmi CommandsIpmi Controller 1Supported Ipmi Commands FRU Information 2Standard FRU Data RecordsSensors 3Threshold SensorsFirmware and Software Upgrades Readme files within the download packageConfiguring the AMC Configuration Tools Boot Bios UtilityLaunching the Boot Bios Utility Features and ConfigurationsPress Ctrl C Page OpenBoot Bios 2Adapter Properties MenuExtensible Firmware Interface EFI Enabling and Disabling Channel PortsConnectors and Ports Connector Pinouts Connector Locations and AssignmentsTable A-1Pin Assignments Appendix a Connectors and Ports SAS Controller Ports Keying Ports 1AMC e-Keying Port AssignmentsPage Environment Specifications Table B-1Electrical Specifications Table B-2Environmental SpecificationsElectrical and Environmental ElectricalTable B-3MTBF Values by Temperature RPMAbsolute Maximum Ratings ReliabilityNormal Operating Ranges AMC.1-HDD SAS disk PCB Dimensions Board Dimensions and WeightMechanical Page Agency Certifications CE Certification NEBS/ETSISafety 1 EN 55022 Emissions Emissions Test Regulations2 EN 55024 Immunity FCC USA Regulatory InformationIndustry Canada Canada Page Index NumericsNEBS/ETSI, C-2
Top Page Image Contents