Sun Microsystems CP3000 manual 6Opening the Injector/Ejector Latch

Page 25

FIGURE 1-6Opening the Injector/Ejector Latch

Figure Legend

1Fully In (IN) When IN, the module communicates to the shelf manager that the module is not in the hot-swap state, and the shelf manager communicates with the MMC. This position is for normal operation.

2Half Way (HW) When in the HW position, the hot-swap sequence is initiated. The MMC sends a hot-swap event to the shelf manager.

Out (OUT) When OUT, the latching mechanism is released and the module can be extracted. Wait

3for the Hot-Swap LED to stop blinking before pulling the latch all the way out.

Chapter 1 Getting Started 1-15

Image 25

Contents For the AMC.1-HDD SAS Disk Please Recycle Contents Managing the AMC OverviewConnectors and Ports Configuring the AMCEnvironment Specifications Agency CertificationsIndex Index-1 Typographic Conventions PrefaceThird-Party Web Sites Related DocumentationSun Welcomes Your Comments Page Getting Started Important Safety Information for Sun Hardware SystemsOperating Systems Compatibility System RequirementsChassis Compatibility Blade Server CompatibilityElectrical and Environmental UnpackingHandling AMCs 1AMC.1-HDD SAS Disk Faceplate AMC Faceplate1AMC Status LEDs AMC LEDs2Hot-Swap Blue LED States Removing an AMC Removing and Installing AMCsShut down the payload OS Hot-Swap LED starts blinking 2Deactivating the AMC 3Removing the AMC Remove the AMC4Front Cable Management Bracket in Lower Position Removing a Blade Server and AMCRemove the filler panel, if necessary Installing an AMC5Sample Top View Obtain the AMC card from the ship kit6Opening the Injector/Ejector Latch Page 7Inserting the AMC Into a Blade Server Push the ejector latch in fullyTo Enable AMC Port 3 Driven by Port 2 of SAS Controller To Enable AMC Port 2 Driven by Port 1 of SAS ControllerPower on the system, if necessary Enabling and Disabling SAS PortsTo Disable AMC Port 3 Driven by Port 2 of SAS Controller To Disable AMC Port 2 Driven by Port 1 of SAS ControllerPage Overview Features Key Components Power RegulatorHard Drive Disk Flash SAS ControllerModule Management Controller MMC Faceplate and LEDs Port ConnectorsLEDs OOS Technical Support and Warranty Functional DiagramPage 4Sun Netra CP3000 AMC.1-HDD SAS disk Barcode Labeling Disposal Managing the AMC Monitoring and Control Functions Supported Ipmi CommandsIpmi Controller 1Supported Ipmi Commands 2Standard FRU Data Records FRU Information3Threshold Sensors SensorsReadme files within the download package Firmware and Software UpgradesConfiguring the AMC Boot Bios Utility Configuration ToolsLaunching the Boot Bios Utility Features and ConfigurationsPress Ctrl C Page 2Adapter Properties Menu OpenBoot BiosEnabling and Disabling Channel Ports Extensible Firmware Interface EFIConnectors and Ports Connector Pinouts Connector Locations and AssignmentsTable A-1Pin Assignments Appendix a Connectors and Ports SAS Controller Ports 1AMC e-Keying Port Assignments Keying PortsPage Environment Specifications Table B-2Environmental Specifications Table B-1Electrical SpecificationsElectrical and Environmental ElectricalRPM Table B-3MTBF Values by TemperatureAbsolute Maximum Ratings ReliabilityNormal Operating Ranges AMC.1-HDD SAS disk PCB Dimensions Board Dimensions and WeightMechanical Page Agency Certifications NEBS/ETSI CE CertificationSafety 1 EN 55022 Emissions Emissions Test Regulations2 EN 55024 Immunity FCC USA Regulatory InformationIndustry Canada Canada Page Numerics IndexNEBS/ETSI, C-2