Sun Microsystems CP3000 manual Faceplate and LEDs, Port Connectors

Page 35

e-Keying as described in the AMC.0 specification

FRU information

LED indicators for hot-swap and OOS (out of service)

2.2.6Port Connectors

The AMC includes connectors to communicate with the host board and take its interfaces outside the ATCA chassis. Refer to Appendix A for complete connector descriptions and pin-outs.

2.2.7LEDs

The AMC.1-HDD SAS disk has three LEDs. See the next section for a detailed description of the LEDs.

2.3Faceplate and LEDs

The faceplate of the AMC.1-HDD SAS disk has three LED indicators, which are described in the table following the faceplate illustration.

Note – The AMC is available in different capacities (in gigabytes). The illustration shows a generic faceplate. For your product’s faceplate, the xxx denotes the capacity.

FIGURE 2-2 Faceplate

Chapter 2 Overview

2-5

Image 35
Contents For the AMC.1-HDD SAS Disk Please Recycle Contents Managing the AMC OverviewAgency Certifications Configuring the AMCConnectors and Ports Environment SpecificationsIndex Index-1 Typographic Conventions PrefaceThird-Party Web Sites Related DocumentationSun Welcomes Your Comments Page Getting Started Important Safety Information for Sun Hardware SystemsBlade Server Compatibility System RequirementsOperating Systems Compatibility Chassis CompatibilityElectrical and Environmental UnpackingHandling AMCs 1AMC.1-HDD SAS Disk Faceplate AMC Faceplate1AMC Status LEDs AMC LEDs2Hot-Swap Blue LED States Shut down the payload OS Removing and Installing AMCsRemoving an AMC Hot-Swap LED starts blinking 2Deactivating the AMC 3Removing the AMC Remove the AMC4Front Cable Management Bracket in Lower Position Removing a Blade Server and AMCRemove the filler panel, if necessary Installing an AMC5Sample Top View Obtain the AMC card from the ship kit6Opening the Injector/Ejector Latch Page 7Inserting the AMC Into a Blade Server Push the ejector latch in fullyEnabling and Disabling SAS Ports To Enable AMC Port 2 Driven by Port 1 of SAS ControllerTo Enable AMC Port 3 Driven by Port 2 of SAS Controller Power on the system, if necessaryTo Disable AMC Port 3 Driven by Port 2 of SAS Controller To Disable AMC Port 2 Driven by Port 1 of SAS ControllerPage Overview Features Hard Drive Disk Power RegulatorKey Components Module Management Controller MMC SAS ControllerFlash LEDs Port ConnectorsFaceplate and LEDs OOS Technical Support and Warranty Functional DiagramPage 4Sun Netra CP3000 AMC.1-HDD SAS disk Barcode Labeling Disposal Managing the AMC Ipmi Controller Supported Ipmi CommandsMonitoring and Control Functions 1Supported Ipmi Commands 2Standard FRU Data Records FRU Information3Threshold Sensors SensorsReadme files within the download package Firmware and Software UpgradesConfiguring the AMC Boot Bios Utility Configuration ToolsPress Ctrl C Features and ConfigurationsLaunching the Boot Bios Utility Page 2Adapter Properties Menu OpenBoot BiosEnabling and Disabling Channel Ports Extensible Firmware Interface EFIConnectors and Ports Table A-1Pin Assignments Connector Locations and AssignmentsConnector Pinouts Appendix a Connectors and Ports SAS Controller Ports 1AMC e-Keying Port Assignments Keying PortsPage Environment Specifications Electrical Table B-1Electrical SpecificationsTable B-2Environmental Specifications Electrical and EnvironmentalRPM Table B-3MTBF Values by TemperatureNormal Operating Ranges ReliabilityAbsolute Maximum Ratings Mechanical Board Dimensions and WeightAMC.1-HDD SAS disk PCB Dimensions Page Agency Certifications NEBS/ETSI CE CertificationSafety 2 EN 55024 Immunity Emissions Test Regulations1 EN 55022 Emissions Industry Canada Canada Regulatory InformationFCC USA Page Numerics IndexNEBS/ETSI, C-2