Sun Microsystems CP3000 manual Mechanical, Board Dimensions and Weight

Page 63

B.3 Mechanical

This section includes the mechanical specifications for dimensions and weight. The AMC.1-HDD SAS disk meets the PICMG 3.0 AdvancedTCA Specification R2.0 ECN002 and AMC.0 R2.0 for all mechanical parameters.

B.3.1 Board Dimensions and Weight

The AMC.1-HDD SAS disk is 181.5 mm by 73.5mm and conforms to the component height requirements of a mid-size module and can be configured as a full-size module. PCI Express x4 connections are made through the AMC edge fingers.

The AMC.1-HDD SAS disk conforms to the PICMG AMC.0 single-width, mid-height AMC Form Factor for all mechanical parameters. Mechanical dimensions are shown in the illustration and are outlined in the following table.

Item

Dimensions or Weight

 

 

PCB

181.5 mm x 73.5 mm x 1.6 mm

Board

AMC.0 R2.0 single-width, full-height form factor

Weight

181.4g

 

 

FIGURE B-1

AMC.1-HDD SAS disk PCB Dimensions

Appendix B Environment Specifications

B-5

Image 63
Contents For the AMC.1-HDD SAS Disk Please Recycle Contents Managing the AMC OverviewAgency Certifications Configuring the AMCConnectors and Ports Environment SpecificationsIndex Index-1 Typographic Conventions PrefaceThird-Party Web Sites Related DocumentationSun Welcomes Your Comments Page Getting Started Important Safety Information for Sun Hardware SystemsBlade Server Compatibility System RequirementsOperating Systems Compatibility Chassis CompatibilityElectrical and Environmental UnpackingHandling AMCs 1AMC.1-HDD SAS Disk Faceplate AMC Faceplate1AMC Status LEDs AMC LEDs2Hot-Swap Blue LED States Removing and Installing AMCs Removing an AMCShut down the payload OS Hot-Swap LED starts blinking 2Deactivating the AMC 3Removing the AMC Remove the AMC4Front Cable Management Bracket in Lower Position Removing a Blade Server and AMCRemove the filler panel, if necessary Installing an AMC5Sample Top View Obtain the AMC card from the ship kit6Opening the Injector/Ejector Latch Page 7Inserting the AMC Into a Blade Server Push the ejector latch in fullyEnabling and Disabling SAS Ports To Enable AMC Port 2 Driven by Port 1 of SAS ControllerTo Enable AMC Port 3 Driven by Port 2 of SAS Controller Power on the system, if necessaryTo Disable AMC Port 3 Driven by Port 2 of SAS Controller To Disable AMC Port 2 Driven by Port 1 of SAS ControllerPage Overview Features Power Regulator Key ComponentsHard Drive Disk SAS Controller FlashModule Management Controller MMC Port Connectors Faceplate and LEDsLEDs OOS Technical Support and Warranty Functional DiagramPage 4Sun Netra CP3000 AMC.1-HDD SAS disk Barcode Labeling Disposal Managing the AMC Supported Ipmi Commands Monitoring and Control FunctionsIpmi Controller 1Supported Ipmi Commands 2Standard FRU Data Records FRU Information3Threshold Sensors SensorsReadme files within the download package Firmware and Software UpgradesConfiguring the AMC Boot Bios Utility Configuration ToolsFeatures and Configurations Launching the Boot Bios UtilityPress Ctrl C Page 2Adapter Properties Menu OpenBoot BiosEnabling and Disabling Channel Ports Extensible Firmware Interface EFIConnectors and Ports Connector Locations and Assignments Connector PinoutsTable A-1Pin Assignments Appendix a Connectors and Ports SAS Controller Ports 1AMC e-Keying Port Assignments Keying PortsPage Environment Specifications Electrical Table B-1Electrical SpecificationsTable B-2Environmental Specifications Electrical and EnvironmentalRPM Table B-3MTBF Values by TemperatureReliability Absolute Maximum RatingsNormal Operating Ranges Board Dimensions and Weight AMC.1-HDD SAS disk PCB DimensionsMechanical Page Agency Certifications NEBS/ETSI CE CertificationSafety Emissions Test Regulations 1 EN 55022 Emissions2 EN 55024 Immunity Regulatory Information FCC USAIndustry Canada Canada Page Numerics IndexNEBS/ETSI, C-2