Sun Microsystems CP3000 manual 2Deactivating the AMC

Page 20

FIGURE 1-2Deactivating the AMC

Figure Legend

1Fully In (IN) When IN, the module communicates to the shelf manager that the module is not in the hot-swap state, and the shelf manager communicates with the MMC. This position is for normal operation.

2Half Way (HW) When in the HW position, the hot-swap sequence is initiated. The MMC sends a hot-swap event to the shelf manager.

Out (OUT) When OUT, the latching mechanism is released and the module can be extracted. Wait

3for the Hot-Swap LED to stop blinking before pulling the latch all the way out.

1-10Sun Netra CP3000 Advanced Mezzanine Card PCIe Hard Drive and SAS Controller User’s Guide • March 2010

Image 20

Contents For the AMC.1-HDD SAS Disk Please Recycle Contents Overview Managing the AMCConfiguring the AMC Connectors and PortsEnvironment Specifications Agency CertificationsIndex Index-1 Preface Typographic ConventionsRelated Documentation Third-Party Web SitesSun Welcomes Your Comments Page Important Safety Information for Sun Hardware Systems Getting StartedSystem Requirements Operating Systems CompatibilityChassis Compatibility Blade Server CompatibilityUnpacking Electrical and EnvironmentalHandling AMCs AMC Faceplate 1AMC.1-HDD SAS Disk FaceplateAMC LEDs 1AMC Status LEDs2Hot-Swap Blue LED States Shut down the payload OS Removing and Installing AMCsRemoving an AMC Hot-Swap LED starts blinking 2Deactivating the AMC Remove the AMC 3Removing the AMCRemoving a Blade Server and AMC 4Front Cable Management Bracket in Lower PositionInstalling an AMC Remove the filler panel, if necessaryObtain the AMC card from the ship kit 5Sample Top View6Opening the Injector/Ejector Latch Page Push the ejector latch in fully 7Inserting the AMC Into a Blade ServerTo Enable AMC Port 2 Driven by Port 1 of SAS Controller To Enable AMC Port 3 Driven by Port 2 of SAS ControllerPower on the system, if necessary Enabling and Disabling SAS PortsTo Disable AMC Port 2 Driven by Port 1 of SAS Controller To Disable AMC Port 3 Driven by Port 2 of SAS ControllerPage Overview Features Hard Drive Disk Power RegulatorKey Components Module Management Controller MMC SAS ControllerFlash LEDs Port ConnectorsFaceplate and LEDs OOS Functional Diagram Technical Support and WarrantyPage 4Sun Netra CP3000 AMC.1-HDD SAS disk Barcode Labeling Disposal Managing the AMC Ipmi Controller Supported Ipmi CommandsMonitoring and Control Functions 1Supported Ipmi Commands FRU Information 2Standard FRU Data RecordsSensors 3Threshold SensorsFirmware and Software Upgrades Readme files within the download packageConfiguring the AMC Configuration Tools Boot Bios UtilityPress Ctrl C Features and ConfigurationsLaunching the Boot Bios Utility Page OpenBoot Bios 2Adapter Properties MenuExtensible Firmware Interface EFI Enabling and Disabling Channel PortsConnectors and Ports Table A-1Pin Assignments Connector Locations and AssignmentsConnector Pinouts Appendix a Connectors and Ports SAS Controller Ports Keying Ports 1AMC e-Keying Port AssignmentsPage Environment Specifications Table B-1Electrical Specifications Table B-2Environmental SpecificationsElectrical and Environmental ElectricalTable B-3MTBF Values by Temperature RPMNormal Operating Ranges ReliabilityAbsolute Maximum Ratings Mechanical Board Dimensions and WeightAMC.1-HDD SAS disk PCB Dimensions Page Agency Certifications CE Certification NEBS/ETSISafety 2 EN 55024 Immunity Emissions Test Regulations1 EN 55022 Emissions Industry Canada Canada Regulatory InformationFCC USA Page Index NumericsNEBS/ETSI, C-2