Paradyne 8784 manual Using the Asynchronous Terminal Interface, User Interface Access

Page 15

Using the Asynchronous

Terminal Interface

User Interface Access

2

You can communicate with the asynchronous terminal interface (ATI) using one of the following methods:

Direct connection through the Management Serial port of the DSLAM (locally or via an external modem).

Telnet session using a Network Management System (NMS) connected to a

TLAN/WAN port on the DSLAM.

Telnet session through the Embedded Operations Channel (EOC).

NOTE:

Only one ATI session can be active at a time, and another user’s session cannot be forced to end. To automatically log out a user due to inactivity, enable the Inactivity Timeout option (see Table A-5, Telnet Session Options, in Appendix A, Configuration Options.

Security can limit ATI access several ways. To set up security or a login ID, refer to Chapter 7, Security.

Management Serial Port Settings

Ensure that the device you connect communicates using these settings:

Data rate set to 9.6 kbps.

Character length set to 8.

TParity set to None. Stop Bits set to 1.

Refer to the installation document for your DSLAM.

8784-A2-GB20-30

February 2001

2-1

Image 15

Contents Hotwire 8784 TDM Sdsl Termination Unit Copyright 2001 Paradyne Corporation All rights reserved Important Safety Instructions United States EMI Notice Contents Initial Startup and Configuration Monitoring the UnitFebruary IP Addressing T TestingMessages and Troubleshooting SecurityStandards ComplianceT for Snmp Traps Configuration OptionsConnector Pin Assignments Technical Specifications Glossary IndexAbout This Guide Document Purpose and Intended AudienceDocument Summary Document Number Document Title Product-Related DocumentsTDM Sdsl Overview About the Hotwire Termination UnitHotwire 8784 Termination Unit Features Network Configuration Customer Premises CPCO Site Network Snmp Management CapabilitiesManagement Information Base MIB Support Snmp Trap SupportUsing the Asynchronous Terminal Interface User Interface AccessManagement Serial Port Settings Logging In to the Hotwire Dslam LoginInitiating an ATI Session Main Menu SelectSnmp Menu HierarchyKeys Main Menu→ Configuration → Current Configuration → NetworkScreen Work Areas FunctionNavigating the Screens Keyboard KeysPress For the screen Function Select Press Enter to Function KeysExample Switching Between Screen Work AreasExiting From the Dslam Session Ending an ATI SessionUsing the Asynchronous Terminal Interface February Overview Initial Startup and ConfigurationEntering Identity Information Main Menu→ Control→ Change IdentityIdentity Configuring the Unit Main Menu→ Configuration Load Configuration FromLoad Configuration from Current and Default Factory Configurations Configuration EDIT/DISPLAYIf you select Then Configuration Loader Configuration LoaderSelect To Access To Configure Main Menu→ Configuration → Configuration LoaderCompleted successfully Save Configuration Saving Configuration ChangesDSL1 Downloading FirmwareMain Menu→ Control → Download Code Download CodeApply Download AutoRate Feature Main Menu→ Configuration→ Current Configuration → NetworkDisabling AutoRate Select Configuration→ DSL Cards → Reset Slot Restoring Access to the User InterfaceResetting AutoRate Main Menu→ Control→ Reset AutoRateMain Menu→ Control→ Reset Device Resetting the UnitWhat to Monitor Monitoring the UnitViewing System and Test Status Main Menu→ Status→ System and Test StatusSystem and Test Status Health and Status SELF-TEST Results Yyyyyyyy Health and Status MessagesMonitoring the Unit Self-Test Results Messages Test Status MessagesTest Status Messages Meaning Viewing Network Error Statistics Network Error StatisticsPerformance Statistics Field Contains SES Severely Errored Seconds Seconds during which more thanViewing Network Performance Statistics This Field Contains Febe Viewing Current Network PerformanceCurrent Network Performance Statistics SESViewing DSX-1 Performance Statistics Main Menu→ Status→ Performance Statistics→ DSX-1 StatisticsDSX-1 Performance Statistics This Field Contains DSL Loop Viewing LED StatusDisplay GeneralFront Panel LEDs TypeLED is Indicating Test TestingAccessing the Test Menu Main Menu→ TestRunning Network Tests Main Menu→ Test→ Network & DSX-1 TestsNetwork & DSX-1 Tests Line Loopback Repeater Loopback DTE Loopback Remote Send Line Loopback Send and Monitor Device Tests Device TestsLamp Test Main Menu→ Test→ Device TestsEnding an Active Test Configuration OptionsActivation Line Payload Remote Line Deactivation Loopback Telco-Initiated TestsTelco-Initiated Line Loopback Telco-Initiated Payload LoopbackCAP LIU DSL DSX-1 Telco-Initiated Remote Line LoopbackTesting February Messages and Troubleshooting Configuring Snmp Traps Snmp Traps OptionsNMS Device Messages 1 What Message Indicates What To Do Device MessagesDevice Messages 2 What Message Indicates What To Do Troubleshooting Symptom Possible Cause Solutions TroubleshootingMessages and Troubleshooting February Security ATI Access LevelsAdminister Logins Creating a LoginOn the Login Entry Screen, for Enter Deleting a LoginConfiguration Options, to Controlling Snmp AccessAssigning Snmp Community Names and Access Types Management Options, in Appendix A, Configuration OptionsSelecting an IP Addressing Scheme Configurations Not Running IP Conservative SoftwareAll Configurations IP AddressingPeer IP Address Assignments IP Addressing ExampleConfiguration Changes in , Initial Startup and Configuration Configuration OptionsTable A-1. Network Interface Options 1 Main Menu→ Configuration→ Current Configuration→ NetworkExcessive Error Rate Threshold Network Interface OptionsCircuit Identifier DSL Line Rate Possible Settings 400, 528, 784, 1040Table A-1. Network Interface Options 2 AutoRateESF Main Menu→ Configuration→ Current Configuration → DSX-1DSX-1 Interface Options DSX-1 Interface OptionsLine Coding Table A-2. DSX-1 Interface Options 1Port Status Line FramingPrimary Clock Source Table A-2. DSX-1 Interface Options 2Send AIS on Network Failure Send All Ones on DSX-1 FailureFrom Port n Main Menu→ Configuration→ Current Configuration→ Copy PortsCopy Ports Options Table A-3. Copy Ports OptionsLTU Main Menu→ Configuration→ Current Configuration→ SystemSystem Options System OptionsTable A-4. System Options Telnet Session Options Management and Communication MenuTable A-5. Telnet Session Options 1 Telnet Login RequiredSession Access Level Inactivity TimeoutDisconnect Time Minutes Main Menu→ Configuration→ Current Configuration→General Snmp Management Options Table A-5. Telnet Session Options 2Snmp Management Name 1 AccessName 2 Access Table A-6. General Snmp Management OptionsSnmp NMS Security Options Snmp NMS Security OptionsAccess Level Table A-7. Snmp NMS Security OptionsNMS IP Validation Snmp Trap Options NMS n Destination Table A-8. Snmp Trap Options 1Snmp Traps Number of Trap ManagersLink Traps Interfaces Link Traps Possible Settings Disable, Up, Down, BothTable A-8. Snmp Trap Options 2 Enterprise Specific TrapsWarmStart AuthenticationFailureStandards Compliance for Snmp Traps Snmp TrapsLinkUp/DownT Variable-Bindings LinkUp and linkDownEnterprise-Specific Traps DSL Network IfIndex RFC Connector Pin Assignments Front Panel 50-pin DTE Connector Pinouts50-Pin Connector DSX-1 Port Pinout Function Connector Pin Assignments February Specifications Criteria Technical SpecificationsTechnical Specifications February COM port Glossary511 Bridged tapFrame Factory defaultsEIA-530-A EthernetIP address Reset703 704Telnet Yellow AlarmRouter RS-449IN-1 IndexIN-2 IN-3 IN-4 IN-5 IN-6