Paradyne 8784 manual General Snmp Management Options, Table A-5. Telnet Session Options 2

Page 86

A. Configuration Options

Table A-5. Telnet Session Options (2 of 2)

Disconnect Time (Minutes)

Possible Settings: 1 – 60

Default Setting: 5

Number of minutes of inactivity before a Telnet session terminates automatically. Timeout is basedTon no keyboard activity.

Disconnect Time (minutes) appears when Inactivity Timeout is enabled. It does not appear when the unit is connected to a DSLAM card running in IP Conservative mode.

1 – 60 – The Telnet session is closed after the selected number of minutes.

General SNMP Management Options

To access the General SNMP Management Options screen, follow this menu selection sequence:

Main Menu→ Configuration→ Current Configuration→

Management and Communication→				General SNMP Management
main/config/management/SNMP				Hotwire
Slot: 4				Model: 8784
	GENERAL SNMP MANAGEMENT OPTIONS
SNMP Management:	Enable
Community Name 1:	Public
Name 1 Access:	Read/Write
Community Name 2:	Public
Name 2 Access:	Read/Write

-------------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous menu	MainMenu Exit
Save

A-12

February 2001

8784-A2-GB20-30

Image 86

Contents Hotwire 8784 TDM Sdsl Termination Unit Copyright 2001 Paradyne Corporation All rights reserved Important Safety Instructions United States EMI Notice Contents February Initial Startup and ConfigurationMonitoring the Unit Security TestingMessages and Troubleshooting IP Addressing TTechnical Specifications Glossary Index Configuration OptionsConnector Pin Assignments Standards ComplianceT for Snmp TrapsDocument Summary About This GuideDocument Purpose and Intended Audience Product-Related Documents Document Number Document TitleAbout the Hotwire Termination Unit TDM Sdsl OverviewHotwire 8784 Termination Unit Features CO Site Network ConfigurationCustomer Premises CP Snmp Trap Support Snmp Management CapabilitiesManagement Information Base MIB Support NetworkManagement Serial Port Settings Using the Asynchronous Terminal InterfaceUser Interface Access Initiating an ATI Session Logging In to the Hotwire DslamLogin Select Main MenuMenu Hierarchy SnmpFunction Main Menu→ Configuration → Current Configuration → NetworkScreen Work Areas KeysPress Navigating the ScreensKeyboard Keys Function Keys For the screen Function Select Press Enter toSwitching Between Screen Work Areas ExampleEnding an ATI Session Exiting From the Dslam SessionUsing the Asynchronous Terminal Interface February Initial Startup and Configuration OverviewIdentity Entering Identity InformationMain Menu→ Control→ Change Identity Load Configuration from Configuring the UnitMain Menu→ Configuration Load Configuration From If you select Then Current and Default Factory ConfigurationsConfiguration EDIT/DISPLAY Main Menu→ Configuration → Configuration Loader Configuration LoaderSelect To Access To Configure Configuration LoaderCompleted successfully Saving Configuration Changes Save ConfigurationDownload Code Downloading FirmwareMain Menu→ Control → Download Code DSL1Apply Download Disabling AutoRate AutoRate FeatureMain Menu→ Configuration→ Current Configuration → Network Main Menu→ Control→ Reset AutoRate Restoring Access to the User InterfaceResetting AutoRate Select Configuration→ DSL Cards → Reset SlotResetting the Unit Main Menu→ Control→ Reset DeviceMonitoring the Unit What to MonitorSystem and Test Status Health and Status SELF-TEST Results Viewing System and Test StatusMain Menu→ Status→ System and Test Status Health and Status Messages YyyyyyyyMonitoring the Unit Test Status Messages Meaning Self-Test Results MessagesTest Status Messages Performance Statistics Viewing Network Error StatisticsNetwork Error Statistics SES Severely Errored Seconds Seconds during which more than Field ContainsViewing Network Performance Statistics This Field Contains SES Viewing Current Network PerformanceCurrent Network Performance Statistics FebeDSX-1 Performance Statistics Viewing DSX-1 Performance StatisticsMain Menu→ Status→ Performance Statistics→ DSX-1 Statistics This Field Contains General Viewing LED StatusDisplay DSL LoopLED is Indicating Front Panel LEDsType Main Menu→ Test TestingAccessing the Test Menu TestNetwork & DSX-1 Tests Running Network TestsMain Menu→ Test→ Network & DSX-1 Tests Line Loopback Repeater Loopback DTE Loopback Remote Send Line Loopback Send and Monitor Main Menu→ Test→ Device Tests Device TestsLamp Test Device TestsConfiguration Options Ending an Active TestTelco-Initiated Payload Loopback Telco-Initiated TestsTelco-Initiated Line Loopback Activation Line Payload Remote Line Deactivation LoopbackTelco-Initiated Remote Line Loopback CAP LIU DSL DSX-1Testing February Messages and Troubleshooting NMS Configuring Snmp TrapsSnmp Traps Options Device Messages Device Messages 1 What Message Indicates What To DoDevice Messages 2 What Message Indicates What To Do Troubleshooting Troubleshooting Symptom Possible Cause SolutionsMessages and Troubleshooting February ATI Access Levels SecurityCreating a Login Administer LoginsDeleting a Login On the Login Entry Screen, for EnterManagement Options, in Appendix A, Configuration Options Controlling Snmp AccessAssigning Snmp Community Names and Access Types Configuration Options, toIP Addressing Configurations Not Running IP Conservative SoftwareAll Configurations Selecting an IP Addressing SchemeIP Addressing Example Peer IP Address AssignmentsConfiguration Options Configuration Changes in , Initial Startup and ConfigurationNetwork Interface Options Main Menu→ Configuration→ Current Configuration→ NetworkExcessive Error Rate Threshold Table A-1. Network Interface Options 1AutoRate DSL Line Rate Possible Settings 400, 528, 784, 1040Table A-1. Network Interface Options 2 Circuit IdentifierDSX-1 Interface Options Main Menu→ Configuration→ Current Configuration → DSX-1DSX-1 Interface Options ESFLine Framing Table A-2. DSX-1 Interface Options 1Port Status Line CodingSend All Ones on DSX-1 Failure Table A-2. DSX-1 Interface Options 2Send AIS on Network Failure Primary Clock SourceTable A-3. Copy Ports Options Main Menu→ Configuration→ Current Configuration→ Copy PortsCopy Ports Options From Port nSystem Options Main Menu→ Configuration→ Current Configuration→ SystemSystem Options LTUTable A-4. System Options Management and Communication Menu Telnet Session OptionsInactivity Timeout Telnet Login RequiredSession Access Level Table A-5. Telnet Session Options 1Table A-5. Telnet Session Options 2 Main Menu→ Configuration→ Current Configuration→General Snmp Management Options Disconnect Time MinutesTable A-6. General Snmp Management Options Name 1 AccessName 2 Access Snmp ManagementSnmp NMS Security Options Snmp NMS Security OptionsNMS IP Validation Access LevelTable A-7. Snmp NMS Security Options Snmp Trap Options Number of Trap Managers Table A-8. Snmp Trap Options 1Snmp Traps NMS n DestinationEnterprise Specific Traps Link Traps Possible Settings Disable, Up, Down, BothTable A-8. Snmp Trap Options 2 Link Traps InterfacesSnmp Traps AuthenticationFailureStandards Compliance for Snmp Traps WarmStartLinkUp and linkDown LinkUp/DownT Variable-BindingsEnterprise-Specific Traps DSL Network IfIndex RFC 50-Pin Connector DSX-1 Port Pinout Function Connector Pin AssignmentsFront Panel 50-pin DTE Connector Pinouts Connector Pin Assignments February Technical Specifications Specifications CriteriaTechnical Specifications February Bridged tap Glossary511 COM portEthernet Factory defaultsEIA-530-A Frame704 Reset703 IP addressRS-449 Yellow AlarmRouter TelnetIndex IN-1IN-2 IN-3 IN-4 IN-5 IN-6