Paradyne 8784 manual System Options, Main Menu→ Configuration→ Current Configuration→ System, Ltu

Page 82

A. Configuration Options

System Options

For System Options, refer to Table A-4, System Options. To access the System Options screen, follow this menu selection sequence:

Main Menu→ Configuration→ Current Configuration→ System

main/config/system	Hotwire
Slot 4	Model: 8784
SYSTEM OPTIONS
DSL Mode:	LTU
Test Timeout:	Enable
Test Duration (min):	10
Telco Initiated Loopbacks:	Enable
Remote Telco Line Loopback:	Disabled

--------------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous menu	MainMenu Exit
Save

A-8

February 2001

8784-A2-GB20-30

Image 82

Contents Hotwire 8784 TDM Sdsl Termination Unit Copyright 2001 Paradyne Corporation All rights reserved Important Safety Instructions United States EMI Notice Contents Monitoring the Unit Initial Startup and ConfigurationFebruary Security TestingMessages and Troubleshooting IP Addressing TTechnical Specifications Glossary Index Configuration OptionsConnector Pin Assignments Standards ComplianceT for Snmp TrapsDocument Purpose and Intended Audience About This GuideDocument Summary Product-Related Documents Document Number Document TitleAbout the Hotwire Termination Unit TDM Sdsl OverviewHotwire 8784 Termination Unit Features Customer Premises CP Network ConfigurationCO Site Snmp Trap Support Snmp Management CapabilitiesManagement Information Base MIB Support NetworkUser Interface Access Using the Asynchronous Terminal InterfaceManagement Serial Port Settings Login Logging In to the Hotwire DslamInitiating an ATI Session Select Main MenuMenu Hierarchy SnmpFunction Main Menu→ Configuration → Current Configuration → NetworkScreen Work Areas KeysKeyboard Keys Navigating the ScreensPress Function Keys For the screen Function Select Press Enter toSwitching Between Screen Work Areas ExampleEnding an ATI Session Exiting From the Dslam SessionUsing the Asynchronous Terminal Interface February Initial Startup and Configuration OverviewMain Menu→ Control→ Change Identity Entering Identity InformationIdentity Main Menu→ Configuration Load Configuration From Configuring the UnitLoad Configuration from Configuration EDIT/DISPLAY Current and Default Factory ConfigurationsIf you select Then Main Menu→ Configuration → Configuration Loader Configuration LoaderSelect To Access To Configure Configuration LoaderCompleted successfully Saving Configuration Changes Save ConfigurationDownload Code Downloading FirmwareMain Menu→ Control → Download Code DSL1Apply Download Main Menu→ Configuration→ Current Configuration → Network AutoRate FeatureDisabling AutoRate Main Menu→ Control→ Reset AutoRate Restoring Access to the User InterfaceResetting AutoRate Select Configuration→ DSL Cards → Reset SlotResetting the Unit Main Menu→ Control→ Reset DeviceMonitoring the Unit What to MonitorMain Menu→ Status→ System and Test Status Viewing System and Test StatusSystem and Test Status Health and Status SELF-TEST Results Health and Status Messages YyyyyyyyMonitoring the Unit Test Status Messages Self-Test Results MessagesTest Status Messages Meaning Network Error Statistics Viewing Network Error StatisticsPerformance Statistics SES Severely Errored Seconds Seconds during which more than Field ContainsViewing Network Performance Statistics This Field Contains SES Viewing Current Network PerformanceCurrent Network Performance Statistics FebeMain Menu→ Status→ Performance Statistics→ DSX-1 Statistics Viewing DSX-1 Performance StatisticsDSX-1 Performance Statistics This Field Contains General Viewing LED StatusDisplay DSL LoopType Front Panel LEDsLED is Indicating Main Menu→ Test TestingAccessing the Test Menu TestMain Menu→ Test→ Network & DSX-1 Tests Running Network TestsNetwork & DSX-1 Tests Line Loopback Repeater Loopback DTE Loopback Remote Send Line Loopback Send and Monitor Main Menu→ Test→ Device Tests Device TestsLamp Test Device TestsConfiguration Options Ending an Active TestTelco-Initiated Payload Loopback Telco-Initiated TestsTelco-Initiated Line Loopback Activation Line Payload Remote Line Deactivation LoopbackTelco-Initiated Remote Line Loopback CAP LIU DSL DSX-1Testing February Messages and Troubleshooting Snmp Traps Options Configuring Snmp TrapsNMS Device Messages Device Messages 1 What Message Indicates What To DoDevice Messages 2 What Message Indicates What To Do Troubleshooting Troubleshooting Symptom Possible Cause SolutionsMessages and Troubleshooting February ATI Access Levels SecurityCreating a Login Administer LoginsDeleting a Login On the Login Entry Screen, for EnterManagement Options, in Appendix A, Configuration Options Controlling Snmp AccessAssigning Snmp Community Names and Access Types Configuration Options, toIP Addressing Configurations Not Running IP Conservative SoftwareAll Configurations Selecting an IP Addressing SchemeIP Addressing Example Peer IP Address AssignmentsConfiguration Options Configuration Changes in , Initial Startup and ConfigurationNetwork Interface Options Main Menu→ Configuration→ Current Configuration→ NetworkExcessive Error Rate Threshold Table A-1. Network Interface Options 1AutoRate DSL Line Rate Possible Settings 400, 528, 784, 1040Table A-1. Network Interface Options 2 Circuit IdentifierDSX-1 Interface Options Main Menu→ Configuration→ Current Configuration → DSX-1DSX-1 Interface Options ESFLine Framing Table A-2. DSX-1 Interface Options 1Port Status Line CodingSend All Ones on DSX-1 Failure Table A-2. DSX-1 Interface Options 2Send AIS on Network Failure Primary Clock SourceTable A-3. Copy Ports Options Main Menu→ Configuration→ Current Configuration→ Copy PortsCopy Ports Options From Port nSystem Options Main Menu→ Configuration→ Current Configuration→ SystemSystem Options LTUTable A-4. System Options Management and Communication Menu Telnet Session OptionsInactivity Timeout Telnet Login RequiredSession Access Level Table A-5. Telnet Session Options 1Table A-5. Telnet Session Options 2 Main Menu→ Configuration→ Current Configuration→General Snmp Management Options Disconnect Time MinutesTable A-6. General Snmp Management Options Name 1 AccessName 2 Access Snmp ManagementSnmp NMS Security Options Snmp NMS Security OptionsTable A-7. Snmp NMS Security Options Access LevelNMS IP Validation Snmp Trap Options Number of Trap Managers Table A-8. Snmp Trap Options 1Snmp Traps NMS n DestinationEnterprise Specific Traps Link Traps Possible Settings Disable, Up, Down, BothTable A-8. Snmp Trap Options 2 Link Traps InterfacesSnmp Traps AuthenticationFailureStandards Compliance for Snmp Traps WarmStartLinkUp and linkDown LinkUp/DownT Variable-BindingsEnterprise-Specific Traps DSL Network IfIndex RFC Front Panel 50-pin DTE Connector Pinouts Connector Pin Assignments50-Pin Connector DSX-1 Port Pinout Function Connector Pin Assignments February Technical Specifications Specifications CriteriaTechnical Specifications February Bridged tap Glossary511 COM portEthernet Factory defaultsEIA-530-A Frame704 Reset703 IP addressRS-449 Yellow AlarmRouter TelnetIndex IN-1IN-2 IN-3 IN-4 IN-5 IN-6