Paradyne 8784 manual Apply Download

Page 33

3. Initial Startup and Configuration

5.Position the cursor at the Start Transfer field. Use the spacebar to select Yes. Press Enter.

When the data transfer is complete:

—If you selected Yes in Step 4, the unit is reset.

—If you selected No, the Transfer Status field changes to Completed successfully.

If you specified No (the default) in the Immediately Apply Download field in Step 4, you must now apply the download.

main/control/apply_download	Hotwire
Slot: 4	Model: 8784

APPLY DOWNLOAD

Switch To Code Revision A01.00.02: No

WARNING:

An answer of “yes” will cause the system

to reset as if it had been powered off and on!

-------------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous		menu	MainMenu Exit
Select: Yes, No	LOS at	Net,	Pt 1

Procedure

To apply the downloaded firmware:

1.Press the Escape key to return to the Control menu. Select Apply Download.

2.On the Apply Download screen, type Yes to reset the card and activate the code.

Selecting Yes causes the termination unit to reset.

NOTE:

The termination unit has two flash memory banks to hold executable firmware. You can switch between these two firmware versions by applying the firmware listed on the Apply Download screen.

8784-A2-GB20-30

February 2001

3-9

Image 33

Contents Hotwire 8784 TDM Sdsl Termination Unit Copyright 2001 Paradyne Corporation All rights reserved Important Safety Instructions United States EMI Notice Contents Initial Startup and Configuration Monitoring the UnitFebruary Messages and Troubleshooting TestingSecurity IP Addressing TConnector Pin Assignments Configuration OptionsTechnical Specifications Glossary Index Standards ComplianceT for Snmp TrapsAbout This Guide Document Purpose and Intended AudienceDocument Summary Document Number Document Title Product-Related DocumentsTDM Sdsl Overview About the Hotwire Termination UnitHotwire 8784 Termination Unit Features Network Configuration Customer Premises CPCO Site Management Information Base MIB Support Snmp Management CapabilitiesSnmp Trap Support NetworkUsing the Asynchronous Terminal Interface User Interface AccessManagement Serial Port Settings Logging In to the Hotwire Dslam LoginInitiating an ATI Session Main Menu SelectSnmp Menu HierarchyScreen Work Areas Main Menu→ Configuration → Current Configuration → NetworkFunction KeysNavigating the Screens Keyboard KeysPress For the screen Function Select Press Enter to Function KeysExample Switching Between Screen Work AreasExiting From the Dslam Session Ending an ATI SessionUsing the Asynchronous Terminal Interface February Overview Initial Startup and ConfigurationEntering Identity Information Main Menu→ Control→ Change IdentityIdentity Configuring the Unit Main Menu→ Configuration Load Configuration FromLoad Configuration from Current and Default Factory Configurations Configuration EDIT/DISPLAYIf you select Then Select To Access To Configure Configuration LoaderMain Menu→ Configuration → Configuration Loader Configuration LoaderCompleted successfully Save Configuration Saving Configuration ChangesMain Menu→ Control → Download Code Downloading FirmwareDownload Code DSL1Apply Download AutoRate Feature Main Menu→ Configuration→ Current Configuration → NetworkDisabling AutoRate Resetting AutoRate Restoring Access to the User InterfaceMain Menu→ Control→ Reset AutoRate Select Configuration→ DSL Cards → Reset SlotMain Menu→ Control→ Reset Device Resetting the UnitWhat to Monitor Monitoring the UnitViewing System and Test Status Main Menu→ Status→ System and Test StatusSystem and Test Status Health and Status SELF-TEST Results Yyyyyyyy Health and Status MessagesMonitoring the Unit Self-Test Results Messages Test Status MessagesTest Status Messages Meaning Viewing Network Error Statistics Network Error StatisticsPerformance Statistics Field Contains SES Severely Errored Seconds Seconds during which more thanViewing Network Performance Statistics This Field Contains Current Network Performance Statistics Viewing Current Network PerformanceSES FebeViewing DSX-1 Performance Statistics Main Menu→ Status→ Performance Statistics→ DSX-1 StatisticsDSX-1 Performance Statistics This Field Contains Display Viewing LED StatusGeneral DSL LoopFront Panel LEDs TypeLED is Indicating Accessing the Test Menu TestingMain Menu→ Test TestRunning Network Tests Main Menu→ Test→ Network & DSX-1 TestsNetwork & DSX-1 Tests Line Loopback Repeater Loopback DTE Loopback Remote Send Line Loopback Send and Monitor Lamp Test Device TestsMain Menu→ Test→ Device Tests Device TestsEnding an Active Test Configuration OptionsTelco-Initiated Line Loopback Telco-Initiated TestsTelco-Initiated Payload Loopback Activation Line Payload Remote Line Deactivation LoopbackCAP LIU DSL DSX-1 Telco-Initiated Remote Line LoopbackTesting February Messages and Troubleshooting Configuring Snmp Traps Snmp Traps OptionsNMS Device Messages 1 What Message Indicates What To Do Device MessagesDevice Messages 2 What Message Indicates What To Do Troubleshooting Symptom Possible Cause Solutions TroubleshootingMessages and Troubleshooting February Security ATI Access LevelsAdminister Logins Creating a LoginOn the Login Entry Screen, for Enter Deleting a LoginAssigning Snmp Community Names and Access Types Controlling Snmp AccessManagement Options, in Appendix A, Configuration Options Configuration Options, toAll Configurations Configurations Not Running IP Conservative SoftwareIP Addressing Selecting an IP Addressing SchemePeer IP Address Assignments IP Addressing ExampleConfiguration Changes in , Initial Startup and Configuration Configuration OptionsExcessive Error Rate Threshold Main Menu→ Configuration→ Current Configuration→ NetworkNetwork Interface Options Table A-1. Network Interface Options 1Table A-1. Network Interface Options 2 DSL Line Rate Possible Settings 400, 528, 784, 1040AutoRate Circuit IdentifierDSX-1 Interface Options Main Menu→ Configuration→ Current Configuration → DSX-1DSX-1 Interface Options ESFPort Status Table A-2. DSX-1 Interface Options 1Line Framing Line CodingSend AIS on Network Failure Table A-2. DSX-1 Interface Options 2Send All Ones on DSX-1 Failure Primary Clock SourceCopy Ports Options Main Menu→ Configuration→ Current Configuration→ Copy PortsTable A-3. Copy Ports Options From Port nSystem Options Main Menu→ Configuration→ Current Configuration→ SystemSystem Options LTUTable A-4. System Options Telnet Session Options Management and Communication MenuSession Access Level Telnet Login RequiredInactivity Timeout Table A-5. Telnet Session Options 1General Snmp Management Options Main Menu→ Configuration→ Current Configuration→Table A-5. Telnet Session Options 2 Disconnect Time MinutesName 2 Access Name 1 AccessTable A-6. General Snmp Management Options Snmp ManagementSnmp NMS Security Options Snmp NMS Security OptionsAccess Level Table A-7. Snmp NMS Security OptionsNMS IP Validation Snmp Trap Options Snmp Traps Table A-8. Snmp Trap Options 1Number of Trap Managers NMS n DestinationTable A-8. Snmp Trap Options 2 Link Traps Possible Settings Disable, Up, Down, BothEnterprise Specific Traps Link Traps InterfacesStandards Compliance for Snmp Traps AuthenticationFailureSnmp Traps WarmStartLinkUp/DownT Variable-Bindings LinkUp and linkDownEnterprise-Specific Traps DSL Network IfIndex RFC Connector Pin Assignments Front Panel 50-pin DTE Connector Pinouts50-Pin Connector DSX-1 Port Pinout Function Connector Pin Assignments February Specifications Criteria Technical SpecificationsTechnical Specifications February 511 GlossaryBridged tap COM portEIA-530-A Factory defaultsEthernet Frame703 Reset704 IP addressRouter Yellow AlarmRS-449 TelnetIN-1 IndexIN-2 IN-3 IN-4 IN-5 IN-6