Patton electronic 2160 user manual Configuring the Model, Web configuration requirements

Page 32

Model 2160 Series User Manual	3 • Hardware installation

Configuring the Model 2160

There are three different ways you can configure the Model 2160: the serial console, Telnet, or a web browser.

Web configuration requirements

Make sure that the PC you use for configuration has an Ethernet adapter and TCP/IP installed.

The Model 2160 provides a browser interface that allows you to configure and manage the Ethernet Extender. After you set up the IP address for the 2160, you can access the Ethernet Extender's Web interface applications directly in your browser by entering the IP address. You can then use your Web browser to manage and config- ure the unit from a PC.

Note For detailed information on configuring the Model 2160 through the

Web interface, see Chapter 4, “Web configuration” on page 33.

Console configuration requirements

To configure the Model 2160 through the serial console, you can directly connect a terminal or a PC equipped with a terminal-emulation program (such as Hyper Terminal) to the Ethernet Extender's console port.

Use the supplied serial cable (RJ-45 to DB9F) to connect the Model 2160 to a PC. After marking the connec- tion, configure the terminal-emulation program to use the following parameters:

•9600 bps

•8 data bits

•no parity

•1 stop bit

Note For detailed information on configuring the Model 2160 through the serial console, see Chapter 5, “Console and Telnet configuration” on page 69.

Telnet configuration requirements

Make sure that the PC you use for configuration has an Ethernet adapter and TCP/IP installed. The Model 2160 supports Telnet for remote configuration. The command is “telnet 192.168.1.1” . When prompted for the username and password for remote login, use admin for username and admin for password. All display screens are the same as serial console configuration.

The default IP address is 192.168.1.1, but you may change the IP address for your application.

Note For detailed information on configuring the Model 2160 through Telnet, see Chapter 5, “Console and Telnet configuration” on page 69.

Configuring the Model 2160

32

Image 32

Contents CopperLink Model 2160 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Web configuration Console and Telnet configuration LAN Vlan Port pin-outs 111 List of Figures Page List of Tables Structure About this guideAudience Precautions Impaired functioningSafety when working with electricity Tected by a circuit breakerPreventing Electrostatic Discharge Damage General observationsTypographical conventions used in this document General conventionsChapter contents General informationModel 2160 overview ModelModel 2160 front panel LED descriptionsModel 2160 rear panel Port descriptionsReset button Ground terminalApplications overview Introduction Typical applicationDistance charts Distance Chart 2160 Series Auto Mode TCPAM-32/16Distance Chart 2160 Series Optimal Mode TCPAM-128 Distance Chart Model 2160 Series Optimal ModeDistance Chart 2160 Series TCPAM-128 Distance Chart Model 2160 Series TCPAM-128Hardware installation Planning the installation IP related information Network diagramAC Power Mains Installing the Model Connecting cablesLocation and mounting requirements Unpacking the ModelGrounding the Model 2160 and connecting power Grounding studConfiguring the Model Web configuration requirementsConsole configuration requirements Telnet configuration requirementsWeb configuration Web configuration System Login Setting Up the WMITCP/IP setup Basic Configuration Options System login screenOperation mode and Management port Dhcp serverBasic Dhcp setup LAN Review and save basic setup changes Review and save basic setup changesAnnex Type Advanced Configuration OptionsLine Type Tcpam Type Main RateSNR Margin Line ProbeVlan VID 802.1Q Tag-Based Vlan 1Q Tag-Based VlanVlan tag field 802.1Q Vlan Port-Based Vlan Port-Based VlanQuality of Service QoS QoSPort Based Priority QoS Port Based PriorityWRR Example SP Example Vlan Tag Priority QoS Vlan Tag PriorityDefault QoS Vlan Tag Priority Table Service by WRR IP Dscp PriorityQoS IP Dscp Priority WRR Configuration Shows the results of the configuration for the LAN 1 port Rate Limit Flow ControlManagement Status Status OptionsLine Status LAN Status Performance StatusUser Profiles Administration OptionsSecurity Administration Snmp Administration Remote Management HostsSnmp Administration Community PoolTrap Host Pool Remote SyslogSystem Information Configuration ToolUtility Options Upgrade UpgradeLogout RestartConsole and Telnet configuration Dhcp Server Dhcp Fixed Host DNS Proxy100 Log in to the console interface Log in using TelnetInterface commands Window structure Product name Line BridgeMain Menu Tree Menu tree for authorized usersMenu tree for unauthorized users Main screen for authorized usersEnable Command Menu Explains the commands available in the main menuSetup Command Menu LineMaximum Main Rate ModeLink Shows the options available within the lan command menu ClearVlan Mode Setup Command Menu Pvid QoS Queue ScheduleQueue Weight This setting configures the weight value for each queueVlan Tag Priority QoS Queue Egress RatePort-Based Priority QoS IP Dscp Priority QoS List RateManagement Address Management IP address and subnet maskDhcp Server Dhcp Fixed HostHost Name Factory DefaultDNS Proxy Status Command Menu LineInterface Status OutDiscardsShow Command Menu Show ScriptPing Command Write CommandReboot Command Ping Command Modify/Add User Administration Command MenuUser Profile Legal IP Address Pool SecurityTelnet TCP Port Snmp CommunityTrap host Please input the following informationSupervisor ID Supervisor Password and IDSupervisor Password Utility Command Menu Upgrade main softwareBackup system configuration Restore system configuration101 Exit Command Contacting Patton for assistance Warranty coverage Contact informationOut-of-warranty service Returns for creditReturn for credit policy RMA numbersAppendix a Compliance information Compliance Radio and TV interference FCC PartCE Declaration of Conformity Authorized European RepresentativeAppendix B Specifications Line Connector Ethernet ConnectorManagement Connector Line ModulationFront Panel Indicators Power SupplyDimensions WeightAppendix C Port pin-outs Console port EIA-561 RJ-45 8-pin portEthernet Line CopperLink