Patton electronic 3088 Series user manual System Configuration Commands, System Status Commands

Page 36

Model 3088 Series User Manual

2 • Configuration

 

 

System Configuration Commands

The following commands allow the user to configure the system:

•system set password <password>: Sets the system password.

•system set circuitid <circuitid>: Sets the circuit ID.

•system set clockmode <internalexternal/networkreceiverecover>: Sets the clock mode. Internal clock mode means the 3088 provides the clock to both the DSL and the serial/T1/E1 interface. External clock mode means the 3088 uses the serial/T1/E1 transmit clock as its DSL transmit clock (V.35 only). Receive recover clock mode means that the 3088 uses the DSL receive clock as its DSL transmit clock and as the serial/T1/E1 receive clock.

Note X.21 External Clock Mode—The X.21 interface expects the DCE to pro- vide the clock used for both transmitting data and for sampling receive data. When the 3088/D is set as a DCE, it may be used in internal or receive recover clock modes. The DSL generates a clock that is provided to the X.21 interface.

When the 3088/D is a DTE, it may be used in external clock mode. The X.21 interface needs to provide the clock. This clock is used by the DSL to sample the serial data and also to update the receive data.

The 3088 is set for either DCE or DTE by flipping the daughter-card. The 3088 is a DCE if DCE points away from the serial interface toward the front of the 3088. Note that this is different than the 3086/D.

The following commands allow the user to view the current system configuration:

•system show config: Shows the configuration of the entire system, including DSL and serial/T1/E1 lines.

Any changes to the system configuration or the DSL configuration will be lost on the next power cycle unless the changes are saved. The command system save config is used to save the changes.

System Status Commands

The following commands show system status:

•system show status: Shows the following system status information: LEDs, DSL test mode, front panel switch settings, DSL link state, and configuration mode.

DSL Configuration Commands

The following commands are used to configure the DSL:

•dsl set timeslots <1–24 (t1) 32 (e1) 72 (v.35, x.21)>: Sets the number of timeslots. For T1/E1 NTU’s, the number of T1/E1 timeslots is set simultaneously. The T1/E1 timeslot mapping will be set to the default. The data rate is calculated by the equation: data-rate = #timeslots x 64k.

•dsl set annex <ab>: Set the annex.

•dsl set lineprobe <enableddisabled>: Enable or disable line probe.

•dsl set loopback <offlalrdl>: Start or stop loopbacks.

•dsl set pattern <off511511e>: Start or stop PRBS generator and BER meter.

Introduction

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Shdsl NTU with fixed serial interface Mailsupport@patton.com Summary Table of Contents Table of Contents RocketLink-G installation Software Upgrade Factory default values List of Figures List of Tables About this guide AudienceStructure Precautions Impaired functioningSafety when working with electricity Typographical conventions used in this document General observationsGeneral conventions Convention MeaningChapter contents General informationFeatures RocketLink-G 3088 overviewSerial interface types Power input connector External AC universal power supplyExternal 48 VDC power supply Configuration Software CLI configuration Hardware DIP-switch configurationIntroduction Parameter Description Possible Values E1-CRCAMI Configuring the DIP switches 3088 K/T ModelsSystem reset mode Software upgradesConfiguration reset to factory defaults DIP switch settingsPosition Function S1-1 S1-2 S1-3 S1-4 S1-5 S1-6 S1-7 Data Rate kbps 2368 S2-4 through S2-5 Clock Mode Models 3088/CA and D S1-8 TX Clock RocketLink-G models 3088/CA and 3088/DS2-2 Line Probe Models 3088/CA and D S2-3 Annex A/B Models 3088/CA and DS2-6 Setting S2-6 DTE Loops RocketLink-G models 3088/CA onlyCPE-Side Modem CO-Side Modem Model 3088/K and 3088/T S1 DIP-Switch Functions 128 S2-4 through S2-5 Clock Mode Models 3088/K and 3088/T S1-7 and S1-8 Line Build Out Models 3088/K and 3088/TS2-2 Line Code Models 3088/K and 3088/T S2-3 Annex A/B Models 3088/K and 3088/TS2-6 through S2-8 Line Type Models 3088/K and 3088/T ConsoleReserved S2-6 S2-7 S2-8 Line TypeConfiguration DSL Line Condition Good or Poor Help Commands System Configuration Commands System Status CommandsDSL Configuration Commands DSL Status Command DSL Clear Errcntrs CommandT1/E1 Configuration Commands Startup Delay Interval Interval totintT1/E1 Status Commands Example Command Line Interface SessionRemote Console RocketLink Plug ‘n’ Play Typical RocketLink Plug ‘n’ Play Application RocketLink-G installation Installation Connecting the twisted pair interfaceConnecting the Model 3088/CA V.35 serial interface Connecting the Model 3088/CA V.35 to a DTE deviceConnecting the Model 3088/CA V.35 to a DCE device Connecting the Model 3088/D X.21 serial interface Connecting the Model 3088/D X.21 to a DCE or DTE deviceConnecting the Model 3088/D to X.21 DTE or DCE Opening the CaseConnecting the Model 3088/K serial interface Connecting the Model 3088/K to an E1 NetworkConnecting dual coaxial cable 75 ohm to E1 network Connect twisted pair 120 ohm to E1 networkConnecting the Model 3088/T T1 serial interface Connect Twisted Pair 100 ohm to T1 NetworkConnecting power External AC universal power supplyDC Power To Power Supply JackOperation Power-up Power GreenLED status monitors DSL GreenTerm Green Models C and D TM/ER RedLOS Red Models K and T Test modesLoopbacks PatternsRemote console operation How to Connect Establishing a Remote Console SessionHow to Disconnect Log in to 3088 Near EndDifferences in Local and Remote Control Session Behavior Remote control session with LAL diagramRemote console operation Software Upgrade Software Upgrade Reset configuration to factory defaults Reset configuration to factory defaults Contacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA Out-of-warranty service Returns for creditReturn for credit policy RMA numbersAppendix a Compliance information Safety ComplianceFCC Part 68 Acta Statement Pstn RegulatoryRadio and TV Interference FCC Part Industry Canada NoticeCE Declaration of Conformity Authorized European Representative Appendix B Specifications Serial connector DiagnosticsClocking modes DTE rateConfiguration Power and power supply specificationsTerm Green Transmission line Line codingLine rates DSL line Line interfaceAppendix C Factory default values Factory default values for software-configurable parameters Parameter Default valueB8ZS Appendix D Factory replacement parts and accessories Factory replacement parts and accessories Model # DescriptionAppendix E Interface pinouts Pin # Signal RJ-11 non-shielded DSL portInterface T1/E1 interfaceSub-15 female connector DTE/DCE orientation RS-232 console interface pin assignments

3088 Series specifications

The Patton Electronics 3088 Series is a robust solution tailored for businesses seeking reliable and efficient data connectivity. This series encompasses a range of devices designed to meet the growing demands of modern networking, particularly in environments that require resilient and secure communications.

One of the standout features of the 3088 Series is its versatile connectivity options. The devices support multiple interfaces, including Ethernet and serial connections, allowing for easy integration into existing infrastructures. This flexibility enables organizations to transition smoothly from outdated systems to state-of-the-art technology without extensive reconfiguration.

The 3088 Series also employs advanced protocols to ensure data integrity and security. Mechanisms such as error correction and data encryption are built into the architecture, safeguarding sensitive information from potential breaches. This is particularly important for industries that handle private data, such as healthcare or finance, where compliance with regulations is critical.

In addition to its connectivity features, the 3088 Series prioritizes ease of use and management. Each device is designed with user-friendly interfaces that simplify configuration and monitoring tasks. Comprehensive management options allow network administrators to efficiently track performance, modify settings, and troubleshoot issues remotely, thereby reducing downtime and maintaining productivity.

Furthermore, the 3088 Series emphasizes durability and reliability, making it suitable for demanding applications. Built using high-quality materials, these devices are engineered to withstand environmental stresses, making them ideal for industrial and outdoor deployments. This resilience contributes to lower maintenance costs and longer lifecycle.

The series is also designed with scalability in mind. As businesses grow and their networking needs evolve, the 3088 Series can adapt accordingly. This feature ensures that organizations can expand their capabilities without completely overhauling their systems, providing a cost-effective long-term solution.

Overall, the Patton Electronics 3088 Series stands out as a powerful and flexible platform for data communications. Its combination of versatile connectivity, high-level security features, ease of management, durability, and scalability render it an ideal choice for organizations looking to future-proof their networking infrastructures. As businesses continue to evolve in a digitally driven landscape, the 3088 Series provides a reliable backbone to support their communication needs.
Top Page Image Contents