Patton electronic 3088 Series Factory default values for software-configurable parameters

Page 76

Model 3088 Series User Manual	C • Factory default values

Factory default values for software-configurable parameters

Table 20. 3088/CA and 3088/D

Parameter	Default value

Clock Mode	Receive-Recover
DSL Timeslots	31

Serial Timeslots	31
Tx Clock	Normal

Circuit ID	Patton Model 3088
Password	superuser

Front Panel Switches	Enabled
Annex	B

Line Probe	Disabled
Loopback	Off

Pattern	Off
DSL Error Monitor – Max Errors/Interval	3

DSL Error Monitor – Interval Time	1
DSL Error Monitor – Max Errored Intervals	3

DSL Error Monitor – Total Intervals	10
DSL Error Monitor – Startup Delay	5

Table 21. 3088/K

Parameter	Default value

Clock Mode	Receive-Recover
DSL Timeslots	31

T1/E1 Timeslots	31
T1/E1 Timeslot Map	1-31

T1/E1 Line Type	E1 - Fractional
T1/E1 Line Code	HDB3

T1/E1 Line Build Out	75 Ohm
T1/E1 Rx Equalizer	Disabled

T1/E1 Pass Framing	Disabled
T1/E1 Pass Alarms	Disabled

Circuit ID	Patton Model 3088
Password	superuser

Front Panel Switches	Enabled
Annex	B

Line Probe	Disabled

Factory default values for software-configurable parameters

76

Image 76

Contents

Shdsl NTU with fixed serial interface Mailsupport@patton.com Summary Table of Contents Table of Contents RocketLink-G installation Software Upgrade Factory default values List of Figures List of Tables Audience About this guideStructure Precautions Impaired functioningSafety when working with electricity Typographical conventions used in this document General observationsGeneral conventions Convention MeaningChapter contents General informationRocketLink-G 3088 overview FeaturesSerial interface types Power input connector External AC universal power supplyExternal 48 VDC power supply Configuration Hardware DIP-switch configuration Software CLI configurationIntroduction Parameter Description Possible Values E1-CRCAMI Configuring the DIP switches 3088 K/T ModelsSystem reset mode Software upgradesConfiguration reset to factory defaults DIP switch settingsPosition Function S1-1 S1-2 S1-3 S1-4 S1-5 S1-6 S1-7 Data Rate kbps 2368 S2-4 through S2-5 Clock Mode Models 3088/CA and D S1-8 TX Clock RocketLink-G models 3088/CA and 3088/DS2-2 Line Probe Models 3088/CA and D S2-3 Annex A/B Models 3088/CA and DS2-6 DTE Loops RocketLink-G models 3088/CA only S2-6 SettingCPE-Side Modem CO-Side Modem Model 3088/K and 3088/T S1 DIP-Switch Functions 128 S2-4 through S2-5 Clock Mode Models 3088/K and 3088/T S1-7 and S1-8 Line Build Out Models 3088/K and 3088/TS2-2 Line Code Models 3088/K and 3088/T S2-3 Annex A/B Models 3088/K and 3088/TS2-6 through S2-8 Line Type Models 3088/K and 3088/T ConsoleReserved S2-6 S2-7 S2-8 Line TypeConfiguration DSL Line Condition Good or Poor Help Commands System Status Commands System Configuration CommandsDSL Configuration Commands DSL Status Command DSL Clear Errcntrs CommandT1/E1 Configuration Commands Startup Delay Interval Interval totintExample Command Line Interface Session T1/E1 Status CommandsRemote Console RocketLink Plug ‘n’ Play Typical RocketLink Plug ‘n’ Play Application RocketLink-G installation Installation Connecting the twisted pair interfaceConnecting the Model 3088/CA V.35 to a DTE device Connecting the Model 3088/CA V.35 serial interfaceConnecting the Model 3088/CA V.35 to a DCE device Connecting the Model 3088/D X.21 serial interface Connecting the Model 3088/D X.21 to a DCE or DTE deviceConnecting the Model 3088/D to X.21 DTE or DCE Opening the CaseConnecting the Model 3088/K serial interface Connecting the Model 3088/K to an E1 NetworkConnecting dual coaxial cable 75 ohm to E1 network Connect twisted pair 120 ohm to E1 networkConnecting the Model 3088/T T1 serial interface Connect Twisted Pair 100 ohm to T1 NetworkConnecting power External AC universal power supplyDC Power To Power Supply JackOperation Power-up Power GreenLED status monitors DSL GreenTerm Green Models C and D TM/ER RedLOS Red Models K and T Test modesLoopbacks PatternsRemote console operation How to Connect Establishing a Remote Console SessionHow to Disconnect Log in to 3088 Near EndDifferences in Local and Remote Control Session Behavior Remote control session with LAL diagramRemote console operation Software Upgrade Software Upgrade Reset configuration to factory defaults Reset configuration to factory defaults Contacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA Out-of-warranty service Returns for creditReturn for credit policy RMA numbersAppendix a Compliance information Safety ComplianceFCC Part 68 Acta Statement Pstn RegulatoryIndustry Canada Notice Radio and TV Interference FCC PartCE Declaration of Conformity Authorized European Representative Appendix B Specifications Serial connector Diagnostics Clocking modes DTE ratePower and power supply specifications ConfigurationTerm Green Transmission line Line codingLine rates DSL line Line interfaceAppendix C Factory default values Factory default values for software-configurable parameters Parameter Default valueB8ZS Appendix D Factory replacement parts and accessories Factory replacement parts and accessories Model # DescriptionAppendix E Interface pinouts Pin # Signal RJ-11 non-shielded DSL portInterface T1/E1 interfaceSub-15 female connector DTE/DCE orientation RS-232 console interface pin assignments