Patton electronic 3088 Series user manual Ami

Page 21

Model 3088 Series User Manual

2 • Configuration

 

 

Table 2. RocketLink-G configurable parameters (Continued)

Parameter

Description

Possible Values

 

 

 

Line Code

Selects line coding for the T1 or E1 line.

AMI

(models K & T)

 

HDB3 (E1 only)

 

 

B8ZS (T1 only)

 

 

 

Line Build Out

Selects wave form used on the T1 or E1 line.

Pulse–75 Ohm(E1)

(models K & T)

 

Pulse–120 Ohm (E1)

 

 

0.0 dB (T1)

 

 

-7.5 dB (T1)

 

 

-15.0 dB (T1)

 

 

-22.5 dB (T1)

RX Equalizer

When enabled, this feature removes signal distortion introduced on

Enabled (select for

(models K & T)

the T1 or E1 cable.

long–haul link).

 

 

Disabled (select for

 

 

short–haul link). Long

 

 

haul LBO (line build-

 

 

out) is defined by

 

 

ANSI T1.403).

 

 

 

Pass Framing

When enabled, the RocketLink-G transparently passes framing infor-

Enabled or Disabled.

(models K & T)

mation (T1 F-bit or E1 TS0) over the DSL link to the remote T1/E1 net-

Must always be

 

work.

enabled for T1.

Pass Alarms

When enabled, the RocketLink-G passes alarms detected on one T1/

Enabled or Disabled

(models K & T)

E1 network over the DSL link to the remote T1/E1 network.

 

 

 

 

Clock Mode

Defines the clock source operation for both DSL and serial/T1/E1

Internal

 

ports as follows. Internal: the on–board oscillator in the 3088 pro-

External

 

vides clock for both serial/T1/E1 and DSL lines. External: the

Receive Recover

 

serial/T1/E1interface provides clock for the DSL line. Receive

 

 

Recover: the DSL interface provides clock for the serial/T1/

 

 

E1 line.

 

Annex

The G.991.2 Annex.

A or B

 

 

 

Line Probe

When this special Patton feature is enabled, the 3088 will set the

Enabled or Disabled

 

DSL data rate to the best rate in the 3–36 timeslot range that both

 

 

NTUs can support. Enable for rate adaptive applications.

 

Loopback

The 3088 provides both a local loopback (LAL) and a remote

OFF, LAL, or RDL

 

loopback (RDL). This can be used to troubleshoot problems.

 

 

 

 

Pattern

The 3088 provides an internal PRBS pattern generator and detec-

OFF, 511, or 511E

 

tor that can be used to run BER tests without external equipment.

 

 

The patterns offered are 511 and 511 with errors.

 

DSL Error Monitor

The number of errors allowed in an interval before considering

0–255

Maximum Intervals

the interval errored. A value of 0 disables the error monitor.

 

 

 

 

Introduction

21

Image 21
Contents Shdsl NTU with fixed serial interface Mailsupport@patton.com Summary Table of Contents Table of Contents RocketLink-G installation Software Upgrade Factory default values List of Figures List of Tables About this guide AudienceStructure Impaired functioning PrecautionsSafety when working with electricity General observations Typographical conventions used in this documentGeneral conventions Convention MeaningGeneral information Chapter contentsFeatures RocketLink-G 3088 overviewSerial interface types External AC universal power supply Power input connectorExternal 48 VDC power supply Configuration Software CLI configuration Hardware DIP-switch configurationIntroduction E1-CRC Parameter Description Possible ValuesAMI 3088 K/T Models Configuring the DIP switchesSoftware upgrades System reset modeConfiguration reset to factory defaults DIP switch settingsPosition Function S1-1 S1-2 S1-3 S1-4 S1-5 S1-6 S1-7 Data Rate kbps 2368 S1-8 TX Clock RocketLink-G models 3088/CA and 3088/D S2-4 through S2-5 Clock Mode Models 3088/CA and DS2-2 Line Probe Models 3088/CA and D S2-3 Annex A/B Models 3088/CA and DS2-6 Setting S2-6 DTE Loops RocketLink-G models 3088/CA onlyCPE-Side Modem CO-Side Modem Model 3088/K and 3088/T S1 DIP-Switch Functions 128 S1-7 and S1-8 Line Build Out Models 3088/K and 3088/T S2-4 through S2-5 Clock Mode Models 3088/K and 3088/TS2-2 Line Code Models 3088/K and 3088/T S2-3 Annex A/B Models 3088/K and 3088/TConsole S2-6 through S2-8 Line Type Models 3088/K and 3088/TReserved S2-6 S2-7 S2-8 Line TypeConfiguration DSL Line Condition Good or Poor Help Commands System Configuration Commands System Status CommandsDSL Configuration Commands DSL Clear Errcntrs Command DSL Status CommandT1/E1 Configuration Commands Startup Delay Interval Interval totintT1/E1 Status Commands Example Command Line Interface SessionRemote Console RocketLink Plug ‘n’ Play Typical RocketLink Plug ‘n’ Play Application RocketLink-G installation Connecting the twisted pair interface InstallationConnecting the Model 3088/CA V.35 serial interface Connecting the Model 3088/CA V.35 to a DTE deviceConnecting the Model 3088/CA V.35 to a DCE device Connecting the Model 3088/D X.21 to a DCE or DTE device Connecting the Model 3088/D X.21 serial interfaceOpening the Case Connecting the Model 3088/D to X.21 DTE or DCEConnecting the Model 3088/K to an E1 Network Connecting the Model 3088/K serial interfaceConnect twisted pair 120 ohm to E1 network Connecting dual coaxial cable 75 ohm to E1 networkConnect Twisted Pair 100 ohm to T1 Network Connecting the Model 3088/T T1 serial interfaceExternal AC universal power supply Connecting powerTo Power Supply Jack DC PowerOperation Power Green Power-upLED status monitors DSL GreenTM/ER Red Term Green Models C and DLOS Red Models K and T Test modesPatterns LoopbacksRemote console operation Establishing a Remote Console Session How to ConnectLog in to 3088 Near End How to DisconnectRemote control session with LAL diagram Differences in Local and Remote Control Session BehaviorRemote console operation Software Upgrade Software Upgrade Reset configuration to factory defaults Reset configuration to factory defaults Contacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA Returns for credit Out-of-warranty serviceReturn for credit policy RMA numbersAppendix a Compliance information Compliance SafetyFCC Part 68 Acta Statement Pstn RegulatoryRadio and TV Interference FCC Part Industry Canada NoticeCE Declaration of Conformity Authorized European Representative Appendix B Specifications Diagnostics Serial connectorClocking modes DTE rateConfiguration Power and power supply specificationsTerm Green Line coding Transmission lineLine rates DSL line Line interfaceAppendix C Factory default values Parameter Default value Factory default values for software-configurable parametersB8ZS Appendix D Factory replacement parts and accessories Model # Description Factory replacement parts and accessoriesAppendix E Interface pinouts RJ-11 non-shielded DSL port Pin # SignalInterface T1/E1 interfaceRS-232 console interface pin assignments Sub-15 female connector DTE/DCE orientation

3088 Series specifications

The Patton Electronics 3088 Series is a robust solution tailored for businesses seeking reliable and efficient data connectivity. This series encompasses a range of devices designed to meet the growing demands of modern networking, particularly in environments that require resilient and secure communications.

One of the standout features of the 3088 Series is its versatile connectivity options. The devices support multiple interfaces, including Ethernet and serial connections, allowing for easy integration into existing infrastructures. This flexibility enables organizations to transition smoothly from outdated systems to state-of-the-art technology without extensive reconfiguration.

The 3088 Series also employs advanced protocols to ensure data integrity and security. Mechanisms such as error correction and data encryption are built into the architecture, safeguarding sensitive information from potential breaches. This is particularly important for industries that handle private data, such as healthcare or finance, where compliance with regulations is critical.

In addition to its connectivity features, the 3088 Series prioritizes ease of use and management. Each device is designed with user-friendly interfaces that simplify configuration and monitoring tasks. Comprehensive management options allow network administrators to efficiently track performance, modify settings, and troubleshoot issues remotely, thereby reducing downtime and maintaining productivity.

Furthermore, the 3088 Series emphasizes durability and reliability, making it suitable for demanding applications. Built using high-quality materials, these devices are engineered to withstand environmental stresses, making them ideal for industrial and outdoor deployments. This resilience contributes to lower maintenance costs and longer lifecycle.

The series is also designed with scalability in mind. As businesses grow and their networking needs evolve, the 3088 Series can adapt accordingly. This feature ensures that organizations can expand their capabilities without completely overhauling their systems, providing a cost-effective long-term solution.

Overall, the Patton Electronics 3088 Series stands out as a powerful and flexible platform for data communications. Its combination of versatile connectivity, high-level security features, ease of management, durability, and scalability render it an ideal choice for organizations looking to future-proof their networking infrastructures. As businesses continue to evolve in a digitally driven landscape, the 3088 Series provides a reliable backbone to support their communication needs.