Patton electronic 3088 Series user manual B8ZS

Page 77

Model 3088 Series User ManualC • Factory default values

Table 21. 3088/K (Continued)

Parameter	Default value

Loopback	Off

Pattern	Off
DSL Error Monitor – Max Errors/Interval	3

DSL Error Monitor – Interval Time	1
DSL Error Monitor – Max Errored Intervals	3

DSL Error Monitor – Total Intervals	10
DSL Error Monitor – Startup Delay	5

Table 22. 3088/T

Parameter	Default value

Clock Mode	Receive-Recover
DSL Timeslots	24

T1/E1 Timeslots	24
T1/E1 Timeslot Map	1-24

T1/E1 Line Type	T1 – ESF
T1/E1 Line Code	B8ZS

T1/E1 Line Build Out	0.0 dB
T1/E1 Rx Equalizer	Disabled

T1/E1 Pass Framing	Disabled
T1/E1 Pass Alarms	Disabled

Circuit ID	Patton Model 3088
Password	Superuser

Front Panel Switches	Enabled
Annex	A

Line Probe	Disabled
Loopback	Off

Pattern	Off
DSL Error Monitor – Max Errors/Interval	3

DSL Error Monitor – Interval Time	1
DSL Error Monitor – Max Errored Intervals	3

DSL Error Monitor – Total Intervals	10
DSL Error Monitor – Startup Delay	5

Factory default values for software-configurable parameters

77

Image 77

Contents

Shdsl NTU with fixed serial interface Mailsupport@patton.com Summary Table of Contents Table of Contents RocketLink-G installation Software Upgrade Factory default values List of Figures List of Tables Structure About this guideAudience Impaired functioning PrecautionsSafety when working with electricity General observations Typographical conventions used in this documentGeneral conventions Convention MeaningGeneral information Chapter contentsSerial interface types FeaturesRocketLink-G 3088 overview External AC universal power supply Power input connectorExternal 48 VDC power supply Configuration Introduction Software CLI configurationHardware DIP-switch configuration E1-CRC Parameter Description Possible ValuesAMI 3088 K/T Models Configuring the DIP switchesSoftware upgrades System reset modeConfiguration reset to factory defaults DIP switch settingsPosition Function S1-1 S1-2 S1-3 S1-4 S1-5 S1-6 S1-7 Data Rate kbps 2368 S1-8 TX Clock RocketLink-G models 3088/CA and 3088/D S2-4 through S2-5 Clock Mode Models 3088/CA and DS2-2 Line Probe Models 3088/CA and D S2-3 Annex A/B Models 3088/CA and DCPE-Side Modem CO-Side Modem S2-6 SettingS2-6 DTE Loops RocketLink-G models 3088/CA only Model 3088/K and 3088/T S1 DIP-Switch Functions 128 S1-7 and S1-8 Line Build Out Models 3088/K and 3088/T S2-4 through S2-5 Clock Mode Models 3088/K and 3088/TS2-2 Line Code Models 3088/K and 3088/T S2-3 Annex A/B Models 3088/K and 3088/TConsole S2-6 through S2-8 Line Type Models 3088/K and 3088/TReserved S2-6 S2-7 S2-8 Line TypeConfiguration DSL Line Condition Good or Poor Help Commands DSL Configuration Commands System Configuration CommandsSystem Status Commands DSL Clear Errcntrs Command DSL Status CommandT1/E1 Configuration Commands Startup Delay Interval Interval totintRemote Console T1/E1 Status CommandsExample Command Line Interface Session RocketLink Plug ‘n’ Play Typical RocketLink Plug ‘n’ Play Application RocketLink-G installation Connecting the twisted pair interface InstallationConnecting the Model 3088/CA V.35 to a DCE device Connecting the Model 3088/CA V.35 serial interfaceConnecting the Model 3088/CA V.35 to a DTE device Connecting the Model 3088/D X.21 to a DCE or DTE device Connecting the Model 3088/D X.21 serial interfaceOpening the Case Connecting the Model 3088/D to X.21 DTE or DCEConnecting the Model 3088/K to an E1 Network Connecting the Model 3088/K serial interfaceConnect twisted pair 120 ohm to E1 network Connecting dual coaxial cable 75 ohm to E1 networkConnect Twisted Pair 100 ohm to T1 Network Connecting the Model 3088/T T1 serial interfaceExternal AC universal power supply Connecting powerTo Power Supply Jack DC PowerOperation Power Green Power-upLED status monitors DSL GreenTM/ER Red Term Green Models C and DLOS Red Models K and T Test modesPatterns LoopbacksRemote console operation Establishing a Remote Console Session How to ConnectLog in to 3088 Near End How to DisconnectRemote control session with LAL diagram Differences in Local and Remote Control Session BehaviorRemote console operation Software Upgrade Software Upgrade Reset configuration to factory defaults Reset configuration to factory defaults Contacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information Returns for credit Out-of-warranty serviceReturn for credit policy RMA numbersAppendix a Compliance information Compliance SafetyFCC Part 68 Acta Statement Pstn RegulatoryCE Declaration of Conformity Radio and TV Interference FCC PartIndustry Canada Notice Authorized European Representative Appendix B Specifications Diagnostics Serial connectorClocking modes DTE rate Term Green Configuration Power and power supply specifications Line coding Transmission lineLine rates DSL line Line interfaceAppendix C Factory default values Parameter Default value Factory default values for software-configurable parametersB8ZS Appendix D Factory replacement parts and accessories Model # Description Factory replacement parts and accessoriesAppendix E Interface pinouts RJ-11 non-shielded DSL port Pin # SignalInterface T1/E1 interfaceRS-232 console interface pin assignments Sub-15 female connector DTE/DCE orientation