Patton electronic 4020 Series manual FXS Port, Ring Setting

Page 76

SmartLink 4020 Getting Started Guide	7 • System

Interdigit Timer

The number of seconds the SmartLink 4020 will wait for the caller to input a subsequent digit of the dialed number. If the timer value is exceeded before the dial plan is matched (see section “Gateway Settings” on page 50), the busy tone will be played to the caller.

Offhook Idle Time

If the handset is off-hook with no dialing activity for longer than the time speciﬁed, then the busy tone will be played. The default is 6000 ms (6 seconds).

Offhook Warning tone time

If the handset is off-hook with no dialing activity for longer than the time speciﬁed, then the off-hook warning tone will be played. The default is 12000 ms (12 seconds). This value should be greater than the off-hook idle time (see section “Offhook Idle Time”).

FXS Port

Choose the correct country for a proper impedance match.

Figure 48. FXS Port Polarity Conﬁguration section of Localization window

FXS port Input Gain

Adjust the input gain level for FXS port.

FXS port Output Gain

Adjust the output gain level for FXS port.

Caller ID Method

Speciﬁes the country-speciﬁc Caller ID format.

“Call Progress Tones” Synchronization

When “Call Progress Tones” Synchronization is selected, the Caller ID presentation method value is used to auto- matically set the county-speciﬁc call progress tones.

Ring Setting

Figure 49. Ring Setting section of Localization window

Ring Waveform

Specify the ring tone waveform.

Localization

76

Image 76

Contents SmartLink Mailsupport@patton.com Summary Table of Contents Table of Contents Vlan Network-LAN Telephony None System Table of Contents Documentation Calling Features List of Figures List of Figures List of Tables Audience About this guideStructure Precautions Safety when working with electricityGeneral observations Typographical conventions used in this documentGeneral conventions Chapter contents General informationSmartLink 4020 overview SmartLinkSmartLink installation Installing the router Do the followingConnect to the Internet service provider Home System information System UptimeSystem information System UptimeWAN IP Address LAN IP AddressSystem Status Network-WAN WAN Priority Tag Ieee 802.1q Status Network SettingsInterface Status Settings Device Operating Mode Internet ConﬁgurationObtain WAN conﬁguration dynamically Specify ﬁxed WAN conﬁgurationEnable PPPoE AuthenticationSettings WAN PPPoE ConﬁgurationMAC Spooﬁng Conﬁguration Conﬁguring Dynamic DNSWAN MAC Address Spoofed WAN Vlan Conﬁguration MTU SizeSaving your work QoS Quality of Service Enable Voice QoSToS/DiffServ Assured Bandwidth for VoiceIPSec Conﬁguration Outbound AH Authentication Algorithm Outbound AH Authentication Key HEXOutbound ESP Authentication Key HEX Inbound AH Authentication AlgorithmInbound ESP Authentication Key HEX Network-LAN Dhcp Server Settings Client Network InformationStatic Address Assignment Viewing the Dchp Client TableRouting Dynamic RoutingStatic Routing Viewing the Routing TablePort Forwarding IP FilteringReserved Ports Port Forwarding to LANFilter IP Range Telephony Telephony Telephony VoIP Server Registration Status VoIP StatusPhone Line Status Caller ID Setting User NameSubscribed for Voicemail Messages waitingGateway Settings SIP Server SettingsSIP Conﬁguration RTP Telephone Event Conﬁguration SIP ExtensionsVoIP Vlan Conﬁguration SIP Timer Values milliseconds SIP ParametersHook Flash Mime Type RTP ParametersNAT Traversal Packetization Audio/CODEC ConﬁgurationJitter Buffer Phone 1 & Phone FAX without T.38 Use G.711 faxSupplementary Service Activation User InformationMessage Waiting Indicator Call Forward AllSelective Call Forward Three-Way ConferencingDial Out Type Call Forward Settings Selective Call Forward SettingsHttp Digest Setting Incoming Call BlockBlock Caller ID Outgoing Call BlockLine 1 Speed Dial Settings Line 2 Speed Dial SettingsSpeed Dial Speed Dial ServSystem System System Set Security Password New Root PasswordNew User Password Web Page ProtectConﬁrm new password Enable SyslogConﬁguration LoggingEnable Debug Debug ServerDebug Connect Port Saving your workService Access Enable HttpEnable Ping Reply LocalizationCall Progress Tones Dial TonePrompt Tone Conﬁrm ToneDistinctive Ring Setting Busy ToneRing Back Tone Off Hook WarningSupplementary Service Keys Name ValueCall forward selective Block Anonymous CallsWarm Line IP DialingIncome Caller ID Speed DialingCalling Preﬁx Keys Voicemail access Call HoldCall Waiting call alternative Call ConferenceControl Timer Values Ring Setting FXS PortFXS Port Polarity Conﬁguration Snmp ConﬁgurationSnmp Trap Conﬁguration Auto Upgrade Routine Upgrade every xxx daysSnmp Community Conﬁguration Snmp System ConﬁgurationManual Upgrade Enable Auto UpgradeAuto Upgrade Protocol Upgrade ServerReload Documentation Introduction Documentation linkLogout Logout window Logout Contacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA Out-of-warranty service Returns for creditReturn for credit policy RMA numbersAppendix a Compliance information Safety Compliance ComplianceRadio and TV Interference CE notice Declaration of ConformityAppendix B Speciﬁcations Voice Processing signalling dependent Voice ConnectivityConnectivity Fax and Modem SupportVoice Services/Features IP ServicesManagement Operating EnvironmentAppendix C Dial plans Sample Dial Plans Simple Dial PlanNon-dialed Line Dial Plan Complex Dial PlanSample Dial Plans Appendix D Calling Features Distinctive on Distinctive OFF