Patton electronic 5400 manual WAN ETH 0/0

Page 17

SmartNode 5400 Getting Started Guide1 • General information

	Table 3. Rear panel ports

Port	Description

WAN ETH 0/0	Auto-MDX Gigabit-Ethernet port, RJ-45 (see figure 1), connects the unit to an Ethernet
	WAN device (for example, a cable modem, DSL modem, or fiber modem). Note:
	Only full duplex modes are supported.
LAN ETH 0/1	Auto-MDX Gigabit-Ethernet port, RJ-45 (see figure 1), connect the unit to an Ethernet
	LAN (for example, a PC, printer, or wireless bridge). Note: Only full duplex modes
	are supported.

Console	Used for service and maintenance, the Console port (see figure 1), an RS-232 RJ-45
	connector, connects the product to a serial terminal such as a PC or ASCII terminal
	(also called a dumb terminal).
Reset	The reset button (see figure 1) has three functions:
	• Restart the unit with the current startup configuration—Press (for less than 1 second)
	and release the Reset button to restart the unit with the current startup configuration.
	• Restart the unit with factory default configuration—Press the Reset button for
	5 seconds until the Power LED (see figure 2 on page 18) starts blinking to restart
	the unit with factory default configuration.
	• Restart the unit in bootloader mode (to be used only by trained SmartNode tech-
	nicians)—Starting with the unit powered off, press and hold the Reset button as
	you apply power to the unit. Release the Reset button when the Power LED starts
	blinking so the unit will enter bootloader mode.

G.SHDSL port	Provides up to 11.4 Mbps (on 4 wires) and 5.7 Mbps (on 2 wires) symmetrical
(option)	throughput, supporting ATM QoS. Supports multiple PVC and DSLAM interoperabil-
	ity. The G.SHDSL LEDs are located on either side of the DSL port. ACT (when lit or
	blinking) shows Activity, and LINK (when lit) shows that the DSL port is connected.

SmartNode 5400 rear panel

17

Image 17

Contents SmartNode 5400 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables Structure About this guideAudience Impaired functioning PrecautionsSafety when working with electricity General observations Convention Meaning Typographical conventions used in this documentGeneral conventions General information Chapter contentsSN5400 model codes SmartNode 5400 overviewSmartNode 5400 rear panel ports are described in table SmartNode 5400 rear panelWAN ETH 0/0 SN5400 SmartNode 5400 front panelDescription LEDApplications overview Typical application IntroductionSmartNode installation Network Diagram Planning the installationSite log Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Internal AC Power Supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCFactory-default IP settings Configuring the desired IP addressLogin Changing the WAN IP addressLAN Connecting the SmartNode to the networkLoading the configuration optional Start Bootloader BootloaderStart-up with factory configuration Step Command PurposeStep Command Purpose Xmodem ymodem -b Load a new application image SmartWare via the serial linkAdditional information Shdsl Basic Configuration Configuring PPPoE Line SetupConfiguration Summary Using PVC channels in bridged Ethernet mode Setting up permanent virtual circuits PVCUsing PVC channels with PPPoE Command PurposeDiagnostics Troubleshooting DSL ConnectionsContacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information RMA numbers Out-of-warranty serviceAppendix a Compliance information Compliance Low-Voltage Directive SafetyCE Declaration of Conformity Authorized European RepresentativeAppendix B Specifications Voice signalling Voice processing signalling dependentData connectivity Fax and modem supportManagement IP servicesSystem PhysicalFactor Specs Shdsl Daughter Card if applicableSmartNode Model SysObjectID Identification of the SmartNode devices via SnmpAppendix C Cabling Console Connecting a serial terminalEthernet Appendix D Port pin-outs Console port Pin SignalShdsl port Appendix E SmartNode 5400 factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination