Patton electronic 5400 manual Shdsl Daughter Card if applicable, Factor Specs

Page 49

SmartNode 5400 Getting Started GuideB • Specifications

G.SHDSL Daughter Card (if applicable)

Note For information on configuring the G.SHDSL daughter card, see Chapter 5, “G.SHDSL Basic Configuration” on page 36.

 

Table 11. G.SHDSL Daughter Card Specifications

 

 

Factor

Specs

 

 

DSL

ITU-T G.991.2 (and Amendment 2)

 

ITU-T G.991.2, Annex A, B, F, G

 

• Upgradable to ITU-T G.shdsl.bis—Annex F and G

 

• G.991.2 2/4 (1/2 pair) operation

 

• G.994.1 (G.hs) (per G.991.2)

 

ITU-T G.991.2 Section E.9

 

(TPS-TC for ATM transport)

DSL Connection

RJ-11/12 (2-wire)

 

 

Management

• I.610 OAM F4/F5

 

• Management interfaces: GUI and Telnet

 

• Software upgrade: GUI and TFTP

ATM Support

• Classical IPoA (RFC 1577/2225)

 

• PPPoE Client (over ATM) (RFC 2516)

 

• IPoA (RFC 2684/1483)

 

• ATM AAL5 encapsulation

 

• Max. 8 PVCs

 

• User selectable VC MUX and LLC MUX (default)

 

• Configurable auto-connection

 

• ATM QoS: UBR (default), CBR, and VBR-rt, VBR-nrt,

 

UBR: per VC queuing

 

Auto-configuration: TR-037 & ILMI 4.0

Interworking/Interoperability • G.SHDSL Interoperability:

-Alcatel

-NEC

-Lucent Anymedia

-Lucent Stinger

BRAS Interoperability:

-Cisco

-Redback

G.SHDSL Daughter Card (if applicable)

49

Image 49
Contents SmartNode 5400 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables Audience About this guideStructure Impaired functioning PrecautionsSafety when working with electricity General observations General conventions Typographical conventions used in this documentConvention Meaning General information Chapter contentsSN5400 model codes SmartNode 5400 overviewSmartNode 5400 rear panel ports are described in table SmartNode 5400 rear panelWAN ETH 0/0 SN5400 SmartNode 5400 front panelDescription LEDApplications overview Typical application IntroductionSmartNode installation Network Diagram Planning the installationSite log Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Internal AC Power Supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCFactory-default IP settings Configuring the desired IP addressLogin Changing the WAN IP addressLAN Connecting the SmartNode to the networkLoading the configuration optional Start Bootloader BootloaderStart-up with factory configuration Step Command PurposeStep Command Purpose Xmodem ymodem -b Load a new application image SmartWare via the serial linkAdditional information Shdsl Basic Configuration Configuring PPPoE Line SetupConfiguration Summary Using PVC channels in bridged Ethernet mode Setting up permanent virtual circuits PVCUsing PVC channels with PPPoE Command PurposeDiagnostics Troubleshooting DSL ConnectionsContacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA RMA numbers Out-of-warranty serviceAppendix a Compliance information Compliance Low-Voltage Directive SafetyCE Declaration of Conformity Authorized European RepresentativeAppendix B Specifications Voice signalling Voice processing signalling dependentData connectivity Fax and modem supportManagement IP servicesSystem PhysicalFactor Specs Shdsl Daughter Card if applicableSmartNode Model SysObjectID Identification of the SmartNode devices via SnmpAppendix C Cabling Console Connecting a serial terminalEthernet Appendix D Port pin-outs Console port Pin SignalShdsl port Appendix E SmartNode 5400 factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination