Patton electronic 5400 manual Internal AC Power Supply

Page 26

SmartNode 5400 Getting Started Guide	3 • SmartNode installation

Connecting the power supply

The 5400 has the option of an internal or external Internal AC Power Supply, or an internal or external Verify that the green Power LED is lit (see figure 5)..

Internal AC Power Supply.

•Do not connect power to the AC Mains at this time.

• There are no user-serviceable parts in the power supply sec

WARNING tion of the Model 5400. Contact Patton Electronics Technical support at (301)975-1007, via our web site at http://www.patton.com, or by e-mail at support@patton.com, for more information.

•The internal power supply automatically adjusts to accept an input voltage from 100 to 240 VAC (50/60 Hz).

Verify that the proper voltage is present before plugging the power cord into the receptacle. Failure to do so could result in equipment damage.

1.Insert the female end of the AC power to the mains port.

–

+

12V,1.	ACT
25A
Power	LI
Power	NK

(~120–240V, 50/60 Hz, 1A)

DSL port (optional)

ETH 0/0

10/100/1000Base-T port

ETH 0/1

10/100/1000Base-T port RESET button

Reset	Console
	Console
	RS-
	232

Console

RS-232 port

Figure 4. 5400 rear panel

2.Verify that the AC power cord included with your router is compatible with local standards. If it is not, refer to “Contacting Patton for assistance” on page 41 to find out how to replace it with a compatible power cord.

3.Connect the male end of the AC power cord to an appropriate AC power outlet.

SmartNode 5400

Enterprise Session Border Router

Power

Figure 5. Power LED

4.Verify that the green Power LED is lit (see figure 5).

Installing the gateway router

26

Image 26

Contents SmartNode 5400 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables Structure About this guideAudience Precautions Impaired functioningSafety when working with electricity General observations Convention Meaning Typographical conventions used in this documentGeneral conventions Chapter contents General informationSmartNode 5400 overview SN5400 model codesSmartNode 5400 rear panel SmartNode 5400 rear panel ports are described in tableWAN ETH 0/0 SmartNode 5400 front panel SN5400LED DescriptionApplications overview Introduction Typical applicationSmartNode installation Site log Planning the installationNetwork Diagram Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Internal AC Power Supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCLogin Configuring the desired IP addressFactory-default IP settings Changing the WAN IP addressConnecting the SmartNode to the network LANLoading the configuration optional Start-up with factory configuration BootloaderStart Bootloader Step Command PurposeStep Command Purpose Load a new application image SmartWare via the serial link Xmodem ymodem -bAdditional information Shdsl Basic Configuration Line Setup Configuring PPPoEConfiguration Summary Using PVC channels with PPPoE Setting up permanent virtual circuits PVCUsing PVC channels in bridged Ethernet mode Command PurposeTroubleshooting DSL Connections DiagnosticsContacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information Out-of-warranty service RMA numbersAppendix a Compliance information CE Declaration of Conformity Low-Voltage Directive SafetyCompliance Authorized European RepresentativeAppendix B Specifications Data connectivity Voice processing signalling dependentVoice signalling Fax and modem supportSystem IP servicesManagement PhysicalShdsl Daughter Card if applicable Factor SpecsIdentification of the SmartNode devices via Snmp SmartNode Model SysObjectIDAppendix C Cabling Connecting a serial terminal ConsoleEthernet Appendix D Port pin-outs Pin Signal Console portShdsl port Appendix E SmartNode 5400 factory configuration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses