Patton electronic 5400 manual Start Bootloader, Start-up with factory configuration

Page 32

SmartNode 5400 Getting Started Guide

4 • Initial configuration

 

 

172.16.1.99(if-ip)[WAN]#reload

Running configuration has been changed.

Do you want to copy the 'running-config' to the 'startup-config'? Press 'yes' to store, 'no' to drop changes : no

Press 'yes' to restart, 'no' to cancel : yes The system is going down

Bootloader

The bootloader ensures that basic operations, network access, and downloads are possible in case of interrupted or corrupted application image downloads. It offers console access to the Bootloader and the capability for downloading application images (e.g. SmartWare) via the serial link of the console.

Start Bootloader

To start the Bootloader, power on the SmartNode while pressing the reset button. Open a Telnet session to the SmartNode via one of the Ethernet interfaces, or open a CLI session via the console port (if available on the SmartNode). The login display will appear. Using the credentials admin / patton , log in to the SmartNode. The following prompt will be displayed:

RedBoot>

Type help to display an overview of the available commands.

Start-up with factory configuration

Step

Command

Purpose

 

 

 

1

RedBoot> fis load

Copies the SmartWare application image from the

 

 

persistent memory (flash:) to the volatile memory

 

 

(RAM) from where it will be executed.

2

RedBoot> go -s factory-config

Starts the SmartWare application telling it to use

 

 

‘factory-config’ as startup configuration.

 

 

You can also start-up with any other configuration

 

 

available in the persistent memory (nvram:) by pro-

 

 

viding its name instead of ‘factory-config’.

 

 

 

Load a new application image (SmartWare) via TFTP

The following procedure downloads the application image (SmartWare) for the mainboard. See the note below on how to download the respective CLI description file.

Step

Command

Purpose

 

 

 

1

RedBoot> ip_address - l

Sets the IP address and subnet mask of the

optional

local_ip_address [/mask_len]

Ethernet interface 0/0 which shall be used to

 

 

receive the new application image.

 

 

mask_len is the length of the network address

 

 

(or the number of 1’s within the subnet mask).

 

 

See Note below.

 

 

 

Bootloader

32

Image 32
Contents SmartNode 5400 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables Structure About this guideAudience Precautions Impaired functioningSafety when working with electricity General observations Convention Meaning Typographical conventions used in this documentGeneral conventions Chapter contents General informationSmartNode 5400 overview SN5400 model codesSmartNode 5400 rear panel SmartNode 5400 rear panel ports are described in tableWAN ETH 0/0 SmartNode 5400 front panel SN5400LED DescriptionApplications overview Introduction Typical applicationSmartNode installation Planning the installation Network DiagramSite log Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Internal AC Power Supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCConfiguring the desired IP address Factory-default IP settingsLogin Changing the WAN IP addressConnecting the SmartNode to the network LANLoading the configuration optional Bootloader Start BootloaderStart-up with factory configuration Step Command PurposeStep Command Purpose Load a new application image SmartWare via the serial link Xmodem ymodem -bAdditional information Shdsl Basic Configuration Line Setup Configuring PPPoEConfiguration Summary Setting up permanent virtual circuits PVC Using PVC channels in bridged Ethernet modeUsing PVC channels with PPPoE Command PurposeTroubleshooting DSL Connections DiagnosticsContacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information Out-of-warranty service RMA numbersAppendix a Compliance information Low-Voltage Directive Safety ComplianceCE Declaration of Conformity Authorized European RepresentativeAppendix B Specifications Voice processing signalling dependent Voice signallingData connectivity Fax and modem supportIP services ManagementSystem PhysicalShdsl Daughter Card if applicable Factor SpecsIdentification of the SmartNode devices via Snmp SmartNode Model SysObjectIDAppendix C Cabling Connecting a serial terminal ConsoleEthernet Appendix D Port pin-outs Pin Signal Console portShdsl port Appendix E SmartNode 5400 factory configuration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses