Patton electronic 5400 manual Step Command Purpose

Page 33

SmartNode 5400 Getting Started Guide4 • Initial configuration

Step

Command

Purpose

 

 

 

2

RedBoot> ip_address -g gateway

Sets the IP address of the default gateway.

optional

 

 

 

 

 

3

RedBoot> ping -htftp-server_ip_address

Tests the connectivity to the TFTP server.

optional

 

 

4

RedBoot> load -r -v -h host -b

Downloads an application image into the vola-

 

base_address file_name

tile memory (RAM) from where the SmartNode

 

 

could directly execute it.

 

 

host: IP address of the TFTP server

 

 

base_address: memory location where to store

 

 

the application image. Use the default address

 

 

0x1800100

 

 

file_name: path and name of the file on the

 

 

TFTP server. Note: use the image file that con-

 

 

tains the whole application, not the image

 

 

parts.

 

 

 

5

RedBoot> fis delete -n 1

Deletes the first application image.

 

 

Reply with ‘y’ to the confirmation request.

6

RedBoot> fis create

Stores the downloaded application image to

 

 

the permanent memory (flash:).

 

 

Reply with ‘y’ to the confirmation request.

 

 

 

7

RedBoot> fis list -l

Checks whether the image has been success-

 

 

fully stored, whether it is the desired Release

 

 

and Build, and whether it is valid.

8

RedBoot> go

Starts the application image that was down-

 

 

loaded into the volatile memory (RAM).

 

 

 

Note With the Bootloader, only the Ethernet interface 0/0 is available. The Boot- loader applies the IP address, subnet mask, and default gateway that were last configured by the Bootloader itself or by another application (e.g. Smart- Ware). If an application configured the Ethernet interface 0/0 to use DHCP, the Bootloader will also use DHCP to learn the interface configuration. It can receive and apply the IP address, subnet mask, default gateway, and default (TFTP) server (transmitted as basic DHCP information ‘Next server IP address’).

Note This procedure does not download the respective CLI description file.

Download it after starting up SmartWare with the following command:

copy tftp://<tftp_server_address>/<server path>/b1 flash:

Example: Downloading and storing a new application image (SmartWare)

RedBoot> ip -l

172.16.40.98/19

RedBoot> ip -g

172.16.32.1

RedBoot> ping -h

172.16.32.100

Network PING -

from 172.16.40.98 to 172.16.32.100

..........PING

-

received 10 of 10 expected

RedBoot> load -r

-v -h 172.16.32.100 -b 0x1800100 /Sn4xxx/image.bin

Bootloader

33

Image 33
Contents SmartNode 5400 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables About this guide AudienceStructure Impaired functioning PrecautionsSafety when working with electricity General observations Typographical conventions used in this document General conventionsConvention Meaning General information Chapter contentsSN5400 model codes SmartNode 5400 overviewSmartNode 5400 rear panel ports are described in table SmartNode 5400 rear panelWAN ETH 0/0 SN5400 SmartNode 5400 front panelDescription LEDApplications overview Typical application IntroductionSmartNode installation Network Diagram Planning the installationSite log Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Internal AC Power Supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCFactory-default IP settings Configuring the desired IP addressLogin Changing the WAN IP addressLAN Connecting the SmartNode to the networkLoading the configuration optional Start Bootloader BootloaderStart-up with factory configuration Step Command PurposeStep Command Purpose Xmodem ymodem -b Load a new application image SmartWare via the serial linkAdditional information Shdsl Basic Configuration Configuring PPPoE Line SetupConfiguration Summary Using PVC channels in bridged Ethernet mode Setting up permanent virtual circuits PVCUsing PVC channels with PPPoE Command PurposeDiagnostics Troubleshooting DSL ConnectionsContacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA RMA numbers Out-of-warranty serviceAppendix a Compliance information Compliance Low-Voltage Directive SafetyCE Declaration of Conformity Authorized European RepresentativeAppendix B Specifications Voice signalling Voice processing signalling dependentData connectivity Fax and modem supportManagement IP servicesSystem PhysicalFactor Specs Shdsl Daughter Card if applicableSmartNode Model SysObjectID Identification of the SmartNode devices via SnmpAppendix C Cabling Console Connecting a serial terminalEthernet Appendix D Port pin-outs Console port Pin SignalShdsl port Appendix E SmartNode 5400 factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination