Patton electronic 5400 manual Termination, Other licenses

Page 61

SmartNode 5400 Getting Started Guide

F • End user license agreement

 

 

If the Program(s) are acquired by or on behalf of a unit or agency of the United States Government, the Gov- ernment agrees that such Program(s) are commercial computer software or computer software documentation and that, absent a written agreement to the contrary, the Government’s rights with respect to such Program(s) are limited by the terms of this Agreement, pursuant to Federal Acquisition Regulations 12.212(a) and/or DEARS 227.7202-1(a) and/or sub-paragraphs (a) through (d) of the “Commercial Computer Software - Restricted Rights” clause at 48 C.F.R. 52.227-19 of the Federal Acquisition Regulations as applicable.

6. Termination

A)The End User may terminate this agreement by returning the Designated Equipment and destroying all copies of the licensed Program(s).

B)Patton Electronics Company may terminate this Agreement should End User violate any of the provi- sions of section “4. Grant of License” on page 60.

C)Upon termination for A or B above or the end of the Term, End User is required to destroy all copies of the licensed Program(s)

7. Other licenses

The Program may be subject to licenses extended by third parties. Accordingly, Patton Electronics Company licenses the Programs subject to the terms and conditions dictated by third parties. Third party software identi- fied to the Programs includes:

A routing license is included at no charge.

The LGPL (Lesser General Public License) open source license distributed to you pursuant to the LGPL license terms (http://www.gnu.org/licenses/lgpl.html).

RedBoot (Red Hat Embedded Debug and Bootstrap) embedded system debug/bootstrap environment from Red Hat distributed to you pursuant to the eCos license terms (http://ecos.sourceware.org/license- overview.html) and GNU General Public License (GPL) terms (http://www.gnu.org/copyleft/gpl.html). Source code is available upon request.

End User License Agreement

61

Image 61
Contents SmartNode 5400 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables Audience About this guideStructure Impaired functioning PrecautionsSafety when working with electricity General observations General conventions Typographical conventions used in this documentConvention Meaning General information Chapter contentsSN5400 model codes SmartNode 5400 overviewSmartNode 5400 rear panel ports are described in table SmartNode 5400 rear panelWAN ETH 0/0 SN5400 SmartNode 5400 front panelDescription LEDApplications overview Typical application IntroductionSmartNode installation Network Diagram Planning the installationSite log Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Internal AC Power Supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCFactory-default IP settings Configuring the desired IP addressLogin Changing the WAN IP addressLAN Connecting the SmartNode to the networkLoading the configuration optional Start Bootloader BootloaderStart-up with factory configuration Step Command PurposeStep Command Purpose Xmodem ymodem -b Load a new application image SmartWare via the serial linkAdditional information Shdsl Basic Configuration Configuring PPPoE Line SetupConfiguration Summary Using PVC channels in bridged Ethernet mode Setting up permanent virtual circuits PVCUsing PVC channels with PPPoE Command PurposeDiagnostics Troubleshooting DSL ConnectionsContacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA RMA numbers Out-of-warranty serviceAppendix a Compliance information Compliance Low-Voltage Directive SafetyCE Declaration of Conformity Authorized European RepresentativeAppendix B Specifications Voice signalling Voice processing signalling dependentData connectivity Fax and modem supportManagement IP servicesSystem PhysicalFactor Specs Shdsl Daughter Card if applicableSmartNode Model SysObjectID Identification of the SmartNode devices via SnmpAppendix C Cabling Console Connecting a serial terminalEthernet Appendix D Port pin-outs Console port Pin SignalShdsl port Appendix E SmartNode 5400 factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination