Patton electronic 5400 manual Led, Description

Page 19

SmartNode 5400 Getting Started Guide1 • General information

 

Table 4. SN5400 Front and Rear panel LEDs

 

 

LED

Description

 

 

Note

If an error occurs, all LEDs will flash once per second.

Power

When lit, indicates power is applied.

 

 

Run

When lit, the unit is in normal operation. Flashes once per second during

 

boot (startup).

VoIP Link

On indicates the gateway is registered to an H.323 gatekeeper/SIP server, or,

 

in the case of direct routing, has at least one active VoIP connection.

 

Off indicates the unit is not configured or registered, or has no active direct-

 

routed VoIP connection.

 

Flashing green indicates that the unit is attempting to register or has failed

 

to register.

 

 

Ethernet Link

On when the Ethernet connection on the corresponding port has a

 

link indication.

Ethernet Speed

When the Ethernet Link LED is on, then:

10/100

On when the Ethernet is connected to a 100Mb network.

 

 

Off when the Ethernet is connected to a 10Mb network.

 

 

Ethernet Speed

On when the Ethernet is connected to a 1000Mb network.

1000

 

Ethernet Activity

Flashes when data is received or transmitted at the corresponding Ethernet port.

 

 

G.SHDSL ACT

Flashes when data is received or transmitted

(Rear panel)

Off = No activity

 

G.SHDSL LINK

On when the G.SHDSL connection on the corresponding port has a

(Rear panel)

link indication.

 

Off = No G.SHDSL connection

 

 

SmartNode 5400 front panel

19

Image 19
Contents SmartNode 5400 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables Audience About this guideStructure Impaired functioning PrecautionsSafety when working with electricity General observations General conventions Typographical conventions used in this documentConvention Meaning General information Chapter contentsSN5400 model codes SmartNode 5400 overviewSmartNode 5400 rear panel ports are described in table SmartNode 5400 rear panelWAN ETH 0/0 SN5400 SmartNode 5400 front panelDescription LEDApplications overview Typical application IntroductionSmartNode installation Network information Planning the installationNetwork Diagram Site logInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Internal AC Power Supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCChanging the WAN IP address Configuring the desired IP addressFactory-default IP settings LoginLAN Connecting the SmartNode to the networkLoading the configuration optional Step Command Purpose BootloaderStart Bootloader Start-up with factory configurationStep Command Purpose Xmodem ymodem -b Load a new application image SmartWare via the serial linkAdditional information Shdsl Basic Configuration Configuring PPPoE Line SetupConfiguration Summary Command Purpose Setting up permanent virtual circuits PVCUsing PVC channels in bridged Ethernet mode Using PVC channels with PPPoEDiagnostics Troubleshooting DSL ConnectionsContacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA RMA numbers Out-of-warranty serviceAppendix a Compliance information Authorized European Representative Low-Voltage Directive SafetyCompliance CE Declaration of ConformityAppendix B Specifications Fax and modem support Voice processing signalling dependentVoice signalling Data connectivityPhysical IP servicesManagement SystemFactor Specs Shdsl Daughter Card if applicableSmartNode Model SysObjectID Identification of the SmartNode devices via SnmpAppendix C Cabling Console Connecting a serial terminalEthernet Appendix D Port pin-outs Console port Pin SignalShdsl port Appendix E SmartNode 5400 factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination