Patton electronic 5400 manual Loading the configuration optional

Page 31

SmartNode 5400 Getting Started Guide

4 • Initial configuration

 

 

You can check the connection with the ping command from the SmartNode to another host on the network.

172.16.1.99(if-ip)[WAN]#ping <IP Address of the host>

Note If the WAN address is not set to DHCP, to ping a device outside your local LAN you must first configure the default gateway. (For information on con- figuring the default gateway, refer to section “Set IP addresses” in Appendix C, “Command Summary” of the SmartNode Series SmartWare Software Con- figuration Guide.)

4. Loading the configuration (optional)

Patton provides a collection of configuration templates on the CD-ROM that came with the SmartNode device—and also on the support page at www.patton.com/voip—one of which may be similar enough to your application that you can use it to speed up configuring the SmartNode. Simply download the configuration note that matches your application to your PC. Adapt the configuration as described in the configuration note to your network (remember to modify the IP address) and copy the modified configuration to a TFTP server. The SmartNode can now load its configuration from this server.

Note Patton regularly adds new configuration templates to the collection at

www.patton.com/voip, so if you do not see your application on the CD-

ROM, it may have been added to the website.

Note If your application is unique and not covered by any of Patton’s configura- tion templates, you can manually configure the SmartNode instead of load- ing a configuration file template. In that case, refer to the SmartNode Series SmartWare Software Configuration Guide for information on configuring the SmartNode device.

In this example we assume the TFTP server on the host with the IP address 172.16.1.11 and the configuration named SN.cfg in the root directory of the TFTP server.

172.16.1.99(if-ip)[WAN]#copy tftp://172.16.1.11/SN.cfg startup-config

Download...100% 172.16.1.99(if-ip)[WAN]#

After the SmartNode has been rebooted the new startup configuration will be activated.

When you issue the reload command, the SmartNode will ask if you want to copy the running configuration to the startup con-

figuration. Since you just downloaded a configuration file to the IMPORTANT startup configuration you must answer this question with NO.

Otherwise, the downloaded configuration will be overwritten and lost!

4. Loading the configuration (optional)

31

Image 31
Contents SmartNode 5400 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables Audience About this guideStructure Impaired functioning PrecautionsSafety when working with electricity General observations General conventions Typographical conventions used in this documentConvention Meaning General information Chapter contentsSN5400 model codes SmartNode 5400 overviewSmartNode 5400 rear panel ports are described in table SmartNode 5400 rear panelWAN ETH 0/0 SN5400 SmartNode 5400 front panelDescription LEDApplications overview Typical application IntroductionSmartNode installation Network information Planning the installationNetwork Diagram Site logInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Internal AC Power Supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCChanging the WAN IP address Configuring the desired IP addressFactory-default IP settings LoginLAN Connecting the SmartNode to the networkLoading the configuration optional Step Command Purpose BootloaderStart Bootloader Start-up with factory configurationStep Command Purpose Xmodem ymodem -b Load a new application image SmartWare via the serial linkAdditional information Shdsl Basic Configuration Configuring PPPoE Line SetupConfiguration Summary Command Purpose Setting up permanent virtual circuits PVCUsing PVC channels in bridged Ethernet mode Using PVC channels with PPPoEDiagnostics Troubleshooting DSL ConnectionsContacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA RMA numbers Out-of-warranty serviceAppendix a Compliance information Authorized European Representative Low-Voltage Directive SafetyCompliance CE Declaration of ConformityAppendix B Specifications Fax and modem support Voice processing signalling dependentVoice signalling Data connectivityPhysical IP servicesManagement SystemFactor Specs Shdsl Daughter Card if applicableSmartNode Model SysObjectID Identification of the SmartNode devices via SnmpAppendix C Cabling Console Connecting a serial terminalEthernet Appendix D Port pin-outs Console port Pin SignalShdsl port Appendix E SmartNode 5400 factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination