TP-Link TL-SL2210WEB/TL-SL2218WEB, TL-SL2428WEB/TL-SL2452WEB manual Connect to Ground

Page 19

Gigabit Uplink Web Smart Switch

2~5kVA

 

Parallel cabling

300

 

 

 

 

 

 

One is in the grounded metal raceway or metal pipe

150

powerline

 

 

 

 

 

 

 

The both are in the grounded metal raceway or metal pipe

80

 

 

 

 

 

 

 

 

>5kVA

 

Parallel cabling

600

 

 

 

 

 

 

One is in the grounded metal raceway or metal pipe

300

powerline

 

 

 

 

 

 

 

The both are in the grounded metal raceway or metal pipe

150

 

 

 

 

 

 

 

 

 

 

 

 

 

Device

 

Min Distance (m1

 

 

 

 

 

 

 

Switch case

 

1.00

 

 

 

 

 

 

Transformer room

2.00

 

 

 

 

 

 

Elevator tower

2.00

 

 

 

 

 

 

Air-conditioner room

2.00

 

 

 

 

 

 

 

 

3.2 Connect to Ground

Connecting the device to ground is to quickly release the lightning over-voltage and over-current of the device, which is also a necessary measure to protect the body from electric shock.

In different environments, the device may be grounded differently. If the device is installed in the normal environment, the device can be grounded via the PE (Protecting Earth\ cable of the AC power supply as shown in the following figure.

FFFFFFFFFFF Connecting to the Ground

Note:

The figure is to illustrate the application and principle. The power plug you get from the package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above.

If you intend to connect the device to the ground via the PE (Protecting Earth\ cable of AC power cord, please make sure the PE (Protecting Earth\ cable in the electrical outlet is well grounded in advance.

Lightning Protection

 

12

 

 

Image 19
Contents User Guide Page CE Mark Warning Copyright & Trademarks FCC StatementRelated Document About this User Guide Conventions AudienceContents WEB Management Cccccccccc Introduction FeaturesProduct Overview Front Panel AppearanceReset Rear Panel Package Contents CCCCCCCCCCInstallationSafety Precautions Site Requirements Lightening Protection Product Installation Installation ToolsFffffffffff Bracket Installation Cabling Reasonably Cccccccccc Lightning ProtectionRequirements for Cabling Indoors Connect to Ground Ethernet Port CCCCCCCCCCConnectionSFP Port Power On Verify InstallationCCCCCCCCCCFunction Description Storm Control Flow ControlPort Security Port Statistic and Port StatusAging Time and Dynamic Address Table Network SettingFiltering MAC Address Table Static MAC Address TableDynamic Binding Vlan Mode Vlan SettingPing Port Trunking Priority Setting Priority ModePort-Based Priority Virtual Cable Test Port Default Priority555555 802.1p Priority Port MirroringCcccccccccweb Management Connecting to the Device Getting StartedOverview Fffffffffff Settings Dialog Dialog will pop up as below Setting the Device Login the SwitchGigabit Uplink Web Smart Switch ¾¾ Port Trunking Port Trunking System Information Further explanation Port Setting Ffffffffffff Port Parameter 66666666Port Statistic 66666666Storm Control Port Status66666666Port Description Static MAC Address Switch IP AddressFFFFFFFFFFFFStatic MAC address Filtering MAC Address 66666666Dynamic Binding Bound MAC Address Aging Time Vlan Setting Vlan Mode 66666666Port Vlan Setting 66666666Tag Vlan Global Setting 66666666Tag Vlan Setting MTU Vlan Setting Priority Setting 66666666Port-Based Priority 66666666802.1p Priority Class FFFFFFFFFFFFVirtual Cable Test Qqqq Why does the Power LED work abnormally? Appendix a TroubleshootingAppendix B Table of Factory Defaults Pvid Appendix C Table of Function Differences of Switch Family FCC, CE Appendix D Hardware SpecificationsAppendix E Technical Support Page 7106503690 Rev