TP-Link TL-SL2428WEB/TL-SL2452WEB, TL-SL2210WEB/TL-SL2218WEB manual Ffffffffffff Port Parameter

Page 38

Gigabit Uplink Web Smart Switch

66666666 Port Parameter

This page contains the following fields:

FFFFFFFFFFFF Port Parameter

¾¾ Port Status: Indicates whether the port is operational or non-operational. "Enable" indicates the port is operational and "Disable" indicates the port is non-operational. If a port is unused for a long time, it can be set to be non-operational to cut down energy costs.

Note: You can't manage the switch via the port, which is non-operational. Please set the value of the management port to be “enable”.

¾¾ Port Security: "Enable" indicates the port will not learn new MAC address and only transmits the frames from the MAC address it has learned. "Disable" indicates it will learn new MAC address.

Caution: If you haven’t set the static MAC address, you can't enable all of the port security, which will result in an inability to manage the switch.

¾¾ Flow Control: Indicates whether the flow control is enabled or disabled.

¾¾ Duplex Mode: Possible field values are Auto, 10Mbps HD, 10Mbps FD, 100Mbps HD, 100Mbps FD and 1000Mbps FD (Giga port support\, "HD" stands for halfduplex and "FD" stands for full-duplex. “Auto” means auto negotiation.

Further explanation:

■■ By operating on fields in the All Ports line expediently, you can set the values of all ports in the corresponding field. Some other setting pages offer the same function.

■■ Parameters of Trunk member ports are configured with default value (see the Appendix B table\ and cannot be configured here (see port 5 and 6 in the Figure 6-22 for example\. For SFP, the Duplex Mode is set to “1000Mbps FD” and cannot be modified.

31 Web Management

Page 37 Page 39
Image 38
Page 37 Page 39
Contents User Guide Page Copyright & Trademarks FCC Statement CE Mark WarningRelated Document About this User Guide Audience ConventionsContents WEB Management Product Overview FeaturesCccccccccc Introduction Appearance Front PanelReset Rear Panel Safety Precautions CCCCCCCCCCInstallationPackage Contents Site Requirements Lightening Protection Installation Tools Product InstallationFffffffffff Bracket Installation Cccccccccc Lightning Protection Cabling ReasonablyRequirements for Cabling Indoors Connect to Ground SFP Port CCCCCCCCCCConnectionEthernet Port Verify Installation Power OnCCCCCCCCCCFunction Description Port Statistic and Port Status Flow ControlPort Security Storm ControlNetwork Setting Aging Time and Dynamic Address TableDynamic Binding Static MAC Address TableFiltering MAC Address Table Ping Vlan SettingVlan Mode Port-Based Priority Priority Setting Priority ModePort Trunking Port Mirroring Port Default Priority555555 802.1p Priority Virtual Cable TestOverview Connecting to the Device Getting StartedCcccccccccweb Management Fffffffffff Settings Dialog Dialog will pop up as below Login the Switch Setting the DeviceGigabit Uplink Web Smart Switch ¾¾ Port Trunking Port Trunking System Information Further explanation Port Setting Ffffffffffff Port Parameter 66666666Port Statistic Port Status 66666666Storm Control66666666Port Description Switch IP Address Static MAC AddressFFFFFFFFFFFFStatic MAC address Filtering MAC Address 66666666Dynamic Binding Bound MAC Address Aging Time Vlan Setting Vlan Mode 66666666Port Vlan Setting 66666666Tag Vlan Global Setting 66666666Tag Vlan Setting MTU Vlan Setting Priority Setting 66666666Port-Based Priority 66666666802.1p Priority Class FFFFFFFFFFFFVirtual Cable Test Appendix a Troubleshooting Qqqq Why does the Power LED work abnormally?Appendix B Table of Factory Defaults Pvid Appendix C Table of Function Differences of Switch Family Appendix D Hardware Specifications FCC, CEAppendix E Technical Support Page 7106503690 Rev
Top Page Image Contents