KTI Networks KSD-800M manual Reset Button, Making UTP Connections

Page 22

2.7 Reset Button

The reset button is used to perform a reset to the switch. It is not used in normal cases and can be used for diagnostic purpose. If any network hanging problem is suspected, it is useful to push the button to reset the switch without turning off the power. Check whether the network is recovered.

The button can also be used to restore the software configuration settings to factory default values. The operations are:

Operation

Function

Press the button more than 5 seconds Press the button less than 5 seconds

Restore the switch back to factory default settings Reboot the switch

2.8 Making UTP Connections

The 10/100TX ports supports the following connection types and distances:

Network Cables

10BASE-T: 2-pair UTP Cat. 3,4,5 , EIA/TIA-568B 100-ohm

100BASE-TX: 2-pair UTP Cat. 5, EIA/TIA-568B 100-ohm

Link distance: Up to 100 meters

Auto MDI/MDI-X Function

This function allows the port to auto-detect the twisted-pair signals and adapts itself to form a valid MDI to MDI-X connection with the remote connected device automatically. No matter a straight through cable or crossover cable is connected, the ports can sense the receiving pair automatically and configure itself to match the rule for MDI to MDI-X connection. It simplifies the cable installation.

Auto-negotiation Function

The ports are featured with auto-negotiation function and full capability to support connection to :

•Auto-negotiation devices

•Auto-negotiation incapable 10BASE-T half duplex devices

•Auto-negotiation incapable 100BASE-TX half duplex devices

It performs a negotiation process for the speed and duplex configuration with the connected device automatically when each time a link is being established. If the connected device is also auto-negotia- tion capable, both devices will come out the best configuration after negotiation process. If the con- nected device is incapable in auto-negotiation, the switch will sense the speed and use half duplex for the connection.

Port Configuration Management

For making proper connection to an auto-negotiation incapable device, it is suggested to use port con- trol function via software management to set forced mode and specify speed and duplex mode which match the configuration used by the connected device.

-22-

Image 22

Contents Installation Guide KSD-800MPage Trademarks Table of Contents Snmp Management Plug and Play IntroductionModel series 10/100TX TP Ports 100FX fiber ports Auto Copper/Fiber ConnectionsBasic functions FeaturesDesigned for Industrial Applications Management functionsProduct Panels Front Panel Network PortsLED Indicators FunctionSpecifications Top PanelLED Indicators Switch Functions10/100TX Twisted Pair Ports Vlan Function Port Configuration Control FunctionSoftware Management Functions QoS FunctionMechanical DC Power InputModel Definitions EnvironmentalOptical Specifications Safety Cautions InstallationUnpacking DIN-Rail Mounting Panel Mounting Page Applying Power Using Terminal BlocksPower Failure Relay Output Using DC Power JackReset Button Making UTP ConnectionsFar End Fault Function Making Fiber ConnectionsLED Indication Function State InterpretationConfiguring Snmp Settings Configuring IP Address for the SwitchConfiguring User Name and Password Configuring Port 7 and PortQoS Function Egress Service PolicyAdvanced Functions Priority LevelDscp Classification per port setting Port-based Priority Setting per port setting3.2 802.1p Classification per port setting User Defined Dscpa Classification GlobalUser Defined IPA Classification Global Other QoS SettingsIP Network Address Classification User Defined IPB Classification GlobalVlan Function Vlan OperationUnmatched VID Filtering per port setting 2.1 802.1Q Tag Aware Vlan Mode global settingIngress Member Filtering global setting Ingress RulesPacket Forwarding under Vlan Egress Tag Rule per port settingVlan Group Mapping Egress Tagging RulesNull VID Replacement per port setting Summary of Vlan FunctionTelnet Management Interface Software ManagementMain Menu IP Settings Description IP MenuSnmp Settings Description Snmp MenuPort Config Status DescriptionAdministrator Vlan Settings AdministratorPort Setting Description Vlan Information Description Vlan IDVID Setting Description Vlan Global Settings DescriptionInput Description Per Port Settings Description Tagging with ingress Pvid for all packetsAdministrator QoS Settings Select 1 Show QoS Other Status to view other settings global QoS Other Settings Description Restore Default Values Security ManagerSetting Description Update FirmwareReboot System ExitWeb Management Login to the Switch UnitStart Browser Software and Making Connection Page Port Status Menu Port Status DescriptionBasic Menu Menu FunctionSystem Settings Description IP Address IP Address Setting DescriptionSnmp Entries Community Settings Description Port Settings Description Trap Manager Settings DescriptionPort Controls Vlan Controls Vlan Group Configuration Global Settings DescriptionIngress Rules Group Settings Description Per Port Settings Egress Rules Insertion for untagged packets only is selectedQoS Per Port Settings Description QoS ControlsQoS Global Settings Description IPA address and IPA subnet mask specify IPA user defined Settings Description Image Refresh TimeRestore Default Snmp Traps Snmp ManagementMIB Objects ObjectsAppendix. Factory Default Settings QoS Settings