KTI Networks KSD-800M manual QoS Other Settings Description

Page 43

Select [2] - [5] to configure other settings as follows:

QoS Other Settings	Description

802.1p priority tag	802.1p High Priority Tag Threshold Setting for 802.1p classification
	Valid values : 0 - 7
Egress service policy	Weighted Round Robin ratio:
	(1) 4:1 - 4 high priority packets then 1 low priority packet
	(2) 8:1 - 8 high priority packets then 1 low priority packet
	(3) 16 :1 - 16 high priority packets then 1 low priority packet
	(4) Always high first - Packets in high priority queue are sent first
	until the queue is empty
Specific DS(A) Setting	Enable - Enable user defined DSCP(A) checking
	Disable - User defined DSCP(A) classification is not applied.
Specific DS(A) Value	Enter user defined DSCP(A) value for classification.
Specific DS(B) Setting	Enable - Enable user defined DSCP(B) checking
	Disable - User defined DSCP(B) classification is not applied.
Specific DS(B) Value	Enter user defined DSCP(B) value for classification.
Specific IP(A) Setting	If a received IP packet’s source address or destination address
	belongs to the user defined IP network addresses. The packet is
	classified as high priority.
	Enable - Enable user defined IP(A) network address checking
	Disable - IP(A) classification is not applied.
Specific IP(A) Value	Set user defined IP(A) address for classification.
Specific IP(A) Mask Value	Set user defined IP(A) subnet mask for classification.
	IP(A) address and IP(A) subnet mask specify IP(A) user defined
	IP network address for IP packet classification.
Specific IP(B) Setting	If a received IP packet’s source address or destination address
	belongs to the user defined IP network addresses. The packet is
	classified as high priority.
	Enable - Enable user defined IP(B) network address checking
	Disable - IP(B) classification is not applied.
Specific IP(B) Value	Set user defined IP(B) address for classification.
Specific IP(B) Mask Value	Set user defined IP(B) subnet mask for classification.
	IP(B) address and IP(B) subnet mask specify IP(B) user defined
	IP network address for IP packet classification.

-43-

Image 43

Contents KSD-800M Installation GuidePage Trademarks Table of Contents Snmp Management Auto Copper/Fiber Connections IntroductionModel series 10/100TX TP Ports 100FX fiber ports Plug and PlayManagement functions FeaturesDesigned for Industrial Applications Basic functionsProduct Panels Network Ports Front PanelFunction LED IndicatorsTop Panel SpecificationsLED Indicators Switch Functions10/100TX Twisted Pair Ports QoS Function Port Configuration Control FunctionSoftware Management Functions Vlan FunctionEnvironmental DC Power InputModel Definitions MechanicalOptical Specifications Safety Cautions InstallationUnpacking DIN-Rail Mounting Panel Mounting Page Using Terminal Blocks Applying PowerUsing DC Power Jack Power Failure Relay OutputMaking UTP Connections Reset ButtonMaking Fiber Connections Far End Fault FunctionFunction State Interpretation LED IndicationConfiguring Port 7 and Port Configuring IP Address for the SwitchConfiguring User Name and Password Configuring Snmp SettingsPriority Level Egress Service PolicyAdvanced Functions QoS FunctionUser Defined Dscpa Classification Global Port-based Priority Setting per port setting3.2 802.1p Classification per port setting Dscp Classification per port settingUser Defined IPB Classification Global Other QoS SettingsIP Network Address Classification User Defined IPA Classification GlobalVlan Operation Vlan FunctionIngress Rules 2.1 802.1Q Tag Aware Vlan Mode global settingIngress Member Filtering global setting Unmatched VID Filtering per port settingEgress Tagging Rules Egress Tag Rule per port settingVlan Group Mapping Packet Forwarding under VlanSummary of Vlan Function Null VID Replacement per port settingTelnet Management Interface Software ManagementMain Menu IP Menu IP Settings DescriptionSnmp Menu Snmp Settings DescriptionStatus Description Port ConfigAdministrator Vlan Settings AdministratorPort Setting Description Vlan ID Vlan Information DescriptionVID Setting Description Vlan Global Settings DescriptionInput Description Tagging with ingress Pvid for all packets Per Port Settings DescriptionAdministrator QoS Settings Select 1 Show QoS Other Status to view other settings global QoS Other Settings Description Security Manager Restore Default ValuesExit Update FirmwareReboot System Setting DescriptionWeb Management Login to the Switch UnitStart Browser Software and Making Connection Page Port Status Description Port Status MenuMenu Function Basic MenuSystem Settings Description IP Address IP Address Setting DescriptionSnmp Entries Community Settings Description Port Settings Description Trap Manager Settings DescriptionPort Controls Vlan Controls Vlan Group Configuration Global Settings DescriptionIngress Rules Group Settings Description Per Port Settings Insertion for untagged packets only is selected Egress RulesQoS Controls QoS Per Port Settings DescriptionQoS Global Settings Description IPA address and IPA subnet mask specify IPA user defined Image Refresh Time Settings DescriptionRestore Default Objects Snmp ManagementMIB Objects Snmp TrapsAppendix. Factory Default Settings QoS Settings