Canon LV-7220, LV-7225, LV-5220 Remote Control Code, Remote Control Battery Installation

Page 14

Part Names and Functions

Remote Control Code

This projector has eight different remote control codes (Code 1-Code 8). Switching remote control codes prevents remote control interference when operating several projectors or video equipment at the same time. Change the remote control code for the projector first before changing that for the remote control unit. See “Remote control” in Setting on page 46.

1	With holding down the MENU button, press the IMAGE
	button. The code switches sequentially for one pressing the
	IMAGE button. (See the list below.)
2	To initialize the		remote control code, slide the
	RESET/ON/ALL-OFF switch to RESET, and then to ON. The
	initial code is Code 1. (p11)

	Remote Control Code		Number of Times of
	Remote Control Code		Pressing IMAGE Button
			Pressing IMAGE Button

	Code 1		1

	Code 2		2

	Code 3		3

	Code 4		4

	Code 5		5

	Code 6		6

	Code 7		7

	Code 8		8

While pressing the MENU button, press the IMAGE button number of times corresponding to the remote control code.

MENU button

IMAGE button

Remote Control Battery Installation

1	Remove the battery
	compartment lid.

Press the lid downward and slide it.

2	Slide the batteries into	3	Replace the compartment
	the compartment.		lid.

Two AA size batteries For correct polarity (+ and

–), be sure battery terminals are in contact with pins in compartment.

To insure safe operation, please observe the following precautions :

●Use (2) AA, UM3 or LR6 type alkaline batteries.

●Replace two batteries at the same time.

●Do not use a new battery with a used battery.

●Avoid contact with water or liquid.

●Do not expose the remote control unit to moisture, or heat.

●Do not drop the remote control unit.

●If a battery has leaked on remote control unit, carefully wipe case clean and install new batteries.

●Risk of explosion if battery is replaced by an incorrect type.

●Dispose of used batteries according to the instructions.

14

Image 14

Contents LV-7225LV-7220LV-5220 See page 32 Features and DesignBlackboard can be used as a projection screen Table of Contents To the Owner Risk of Electric Shock Do not OpenSafety Instructions Hinweise für DeutschlandMoving the Projector Installing the Projector in Proper PositionAir Circulation Compliance Federal Communication Commission NoticeLens Cover See page 50 for attaching Part Names and FunctionsFront Back Bottom Rear Terminal Top Control Remote Control Unit Signal Emission indicatorLaser Pointer Function Pointer FunctionWireless Mouse Operation Operating RangeButton. The code switches sequentially for one pressing Remote Control CodeRemote Control Battery Installation With holding down the Menu button, press the ImagePositioning the Projector InstallationAdjustable Feet 200 240 V AC Connecting the AC Power CordFor the U.S.A. and Canada For Continental Europe Connecting to a Computer Cables used for connectionConnecting to Video Equipment StereoConnecting to Component Video Equipment Component RGB OUTTurning On the Projector What is PIN code?Basic Operation Enter a PIN codeDisconnect the AC power cord When the projector has cooled down enough to be turned onAgain, the Power indicator lights red. Then you can Turning Off the ProjectorOn-Screen Menu How to Operate the On-Screen MenuRemote Control Unit Top ControlMenu Bar PC System MenuZoom and Focus Adjustment Auto Setup FunctionNo Show Function Keystone AdjustmentPicture Freeze Function Volume Timer FunctionSound Adjustment MuteComputer Input Input Source SelectionMode Computer System SelectionAuto PC Adjust Menu Auto PC AdjustmentTo store adjustment parameters Auto PC AdjManual PC Adjustment Display area ResetMode free Display area HHigh contrast Image Level SelectionStandard BlackboardGreenImage Level Adjustment Screen Size Adjustment Input button Video Computer Video button Video InputInput Source Selection Video, S-Video Source Select Menu VideoInput Source Selection Component, RGB Scart 21-Pin Input button Computer Video Computer buttonAV System Menu Video or S-Video Video System SelectionAuto AV System Menu ComponentCinema Picture level adjusted for the picture with fine toneUser preset image in the Image Adjust Menu p39 Image button Standard Cinema BlackboardGreen CustomPress the Point 78 button to obtain proper color. From 0 to ColorTint Film Resets all adjustment to their previous figureProgressive Provides image at a normal video aspect ratio of 4 Provides image at a wide screen ratio of 16Auto setup SettingSetting LanguageLogo PIN code lock Blue backDisplay Enter a Logo PIN codeCeiling LogoCapture RearLamp mode Standby modePower management On startUSB Remote controlPointer Key lockTo Change the PIN code To Change the PIN code lock settingPIN code lock Fan Factory default Lamp counter resetFactory default FanThen check the matters below Maintenance and CleaningProjector is shut down and the Warning indicator lights red Cleaning the Air Filters Attaching the Lens CoverCleaning the Projection Lens Cleaning the Projector CabinetLamp Replacement Reset the Lamp replace counterWhen the lamp replace counter is reset, the Lamp Lamp Replace CounterTroubleshooting AppendixRemote Control Unit does not work. Check the batteries AppendixMenu Tree Setting Image Select Image Adjust ScreenIndicators and Projector Condition KHz Compatible Computer SpecificationsFreq Technical Specifications This cable is used for RGB 21-Pin Optional PartsLV-CA31 Not available in the U.S.A Video output of video equipmentTerminal HDB15-PIN Configurations of TerminalsUSB Connector Series B Terminal DVI-IWhile the projector is locked with the PIN code Canon Communication & Image France S.A 1AA6P1P4619--MT7P