Canon LV-7225, LV-5220, LV-7220 Installation, Positioning the Projector, Adjustable Feet

Page 15

Installation

Positioning the Projector

This projector is designed to project on a flat projection surface and can be focused from 3.3’(1.0m) - 25.3’(7.7m). Refer to the figure and the table below for the screen size and the distance between the projector and the screen.

A : B = 9 : 1

25.3' (7.7m)

16.1' (4.9m)

(Inch Diagonal)

300”

12.5' (3.8m)

8.2' (2.5m)

3.3' (1.0m)

100”

40”62”

150”

95”

190”

122”

Max. Zoom

190”

A

Min. Zoom

(Center)

B

Installation

Screen Size

 

40”

 

100”

150”

190”

300”

(W x H) mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

813 x 610

 

2032 x 1524

3048 x 2286

3861 x 2896

6096 x 4572

4 : 3 aspect ratio

 

 

 

 

 

 

 

 

 

 

Zoom (min)

 

5.2' (1.6m)

 

13.1' (4.0m)

19.7 (6.0m)

25.3' (7.7m)

––-––

 

 

 

 

 

 

 

 

Zoom (max)

 

3.3' (1.0m)

 

8.2' (2.5m)

12.5' (3.8m)

16.1' (4.9m)

25.3' (7.7m)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note:

The brightness in a room has a great influence on picture quality. It is recommended to limit ambient lighting in order to obtain the best image.

The values shown above are approximate and may vary from the actual size.

Adjustable Feet

Projection angle can be adjusted up to 11.9 degrees with the adjustable feet.

1

Lift the front of the projector and pull upward the feet lock

 

latches on both sides of the projector.

2

Release the feet lock latches to lock the adjustable feet and

 

rotate the adjustable feet to adjust the position and tilt.

3

To retract the adjustable feet, lift the front of the projector

 

and pull and undo the feet lock latches.

Keystone distortion of the projected image can be adjusted automatically with Auto Setup function or manually with the remote control unit or the menu operation. (p24, 25, and 42)

Feet Lock Latches

Adjustable Feet

15

Image 15
Contents LV-7225LV-7220LV-5220 Features and Design Blackboard can be used as a projection screenSee page 32 Table of Contents Risk of Electric Shock Do not Open To the OwnerHinweise für Deutschland Safety InstructionsInstalling the Projector in Proper Position Air CirculationMoving the Projector Federal Communication Commission Notice CompliancePart Names and Functions Front Back BottomLens Cover See page 50 for attaching Rear Terminal Top Control Signal Emission indicator Remote Control UnitPointer Function Laser Pointer FunctionOperating Range Wireless Mouse OperationWith holding down the Menu button, press the Image Remote Control CodeRemote Control Battery Installation Button. The code switches sequentially for one pressingInstallation Adjustable FeetPositioning the Projector Connecting the AC Power Cord For the U.S.A. and Canada For Continental Europe200 240 V AC Cables used for connection Connecting to a ComputerStereo Connecting to Video EquipmentComponent RGB OUT Connecting to Component Video EquipmentEnter a PIN code What is PIN code?Basic Operation Turning On the ProjectorTurning Off the Projector When the projector has cooled down enough to be turned onAgain, the Power indicator lights red. Then you can Disconnect the AC power cordTop Control How to Operate the On-Screen MenuRemote Control Unit On-Screen MenuPC System Menu Menu BarAuto Setup Function Zoom and Focus AdjustmentKeystone Adjustment Picture Freeze FunctionNo Show Function Mute Timer FunctionSound Adjustment VolumeInput Source Selection Computer InputComputer System Selection AutoMode Auto PC Adj Auto PC AdjustmentTo store adjustment parameters PC Adjust MenuManual PC Adjustment Display area H ResetMode free Display areaBlackboardGreen Image Level SelectionStandard High contrastImage Level Adjustment Screen Size Adjustment Source Select Menu Video Video InputInput Source Selection Video, S-Video Input button Video Computer Video buttonInput button Computer Video Computer button Input Source Selection Component, RGB Scart 21-PinAV System Menu Component Video System SelectionAuto AV System Menu Video or S-VideoImage button Standard Cinema BlackboardGreen Custom Picture level adjusted for the picture with fine toneUser preset image in the Image Adjust Menu p39 CinemaColor TintPress the Point 78 button to obtain proper color. From 0 to Resets all adjustment to their previous figure ProgressiveFilm Provides image at a wide screen ratio of 16 Provides image at a normal video aspect ratio of 4Language SettingSetting Auto setupEnter a Logo PIN code Blue backDisplay Logo PIN code lockRear LogoCapture CeilingOn start Standby modePower management Lamp modeKey lock Remote controlPointer USBTo Change the PIN code lock setting PIN code lockTo Change the PIN code Fan Lamp counter resetFactory default Fan Factory defaultMaintenance and Cleaning Projector is shut down and the Warning indicator lights redThen check the matters below Attaching the Lens Cover Cleaning the Air FiltersCleaning the Projector Cabinet Cleaning the Projection LensReset the Lamp replace counter Lamp ReplacementLamp Replace Counter When the lamp replace counter is reset, the LampAppendix TroubleshootingAppendix Remote Control Unit does not work. Check the batteriesMenu Tree Image Select Image Adjust Screen SettingIndicators and Projector Condition Compatible Computer Specifications FreqKHz Technical Specifications Video output of video equipment Optional PartsLV-CA31 Not available in the U.S.A This cable is used for RGB 21-PinTerminal DVI-I Configurations of TerminalsUSB Connector Series B Terminal HDB15-PINWhile the projector is locked with the PIN code 1AA6P1P4619--MT7P Canon Communication & Image France S.A