Canon LV-5220 Connecting the AC Power Cord, For the U.S.A. and Canada For Continental Europe

Page 16

Installation

Connecting the AC Power Cord

This projector uses nominal input voltages of 100-120 V or 200-240 V AC. This projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system.

Consult your authorized dealer or service station if you are not sure of the type of power being supplied.

Connect the projector with all peripheral equipment before turning the projector on. (See page 17-19 for connection.)

CAUTION

For safety, unplug AC power cord when the projector is not in use. When this projector is connected to an outlet with AC power cord, it is in Stand-by mode and consumes a little electric power.

Connect AC power cord (supplied) to the projector.

The AC outlet must be near this equipment and must be easily accessible.

NOTE ON THE POWER CORD

AC power cord must meet requirement of the country where you use a projector. Confirm an AC plug type with the chart below and proper AC power cord must be used. If supplied AC power cord does not match your AC outlet, contact your sales dealer.

	Projector side	AC outlet side
		For the U.S.A. and Canada	For Continental Europe
		Ground
	To power cord	To the AC outlet.	To the AC outlet.
	connector on your	To the AC outlet.
	connector on your	(120 V AC)
	projector.	(120 V AC)	(200 - 240 V AC)
	projector.		(200 - 240 V AC)

16

Image 16

Contents LV-7225LV-7220LV-5220 Blackboard can be used as a projection screen Features and DesignSee page 32 Table of Contents To the Owner Risk of Electric Shock Do not OpenSafety Instructions Hinweise für DeutschlandAir Circulation Installing the Projector in Proper PositionMoving the Projector Compliance Federal Communication Commission NoticeFront Back Bottom Part Names and FunctionsLens Cover See page 50 for attaching Rear Terminal Top Control Remote Control Unit Signal Emission indicatorLaser Pointer Function Pointer FunctionWireless Mouse Operation Operating RangeRemote Control Code Remote Control Battery InstallationButton. The code switches sequentially for one pressing With holding down the Menu button, press the ImageAdjustable Feet InstallationPositioning the Projector For the U.S.A. and Canada For Continental Europe Connecting the AC Power Cord200 240 V AC Connecting to a Computer Cables used for connectionConnecting to Video Equipment StereoConnecting to Component Video Equipment Component RGB OUTWhat is PIN code? Basic OperationTurning On the Projector Enter a PIN codeWhen the projector has cooled down enough to be turned on Again, the Power indicator lights red. Then you canDisconnect the AC power cord Turning Off the ProjectorHow to Operate the On-Screen Menu Remote Control UnitOn-Screen Menu Top ControlMenu Bar PC System MenuZoom and Focus Adjustment Auto Setup FunctionPicture Freeze Function Keystone AdjustmentNo Show Function Timer Function Sound AdjustmentVolume MuteComputer Input Input Source SelectionAuto Computer System SelectionMode Auto PC Adjustment To store adjustment parametersPC Adjust Menu Auto PC AdjManual PC Adjustment Reset Mode freeDisplay area Display area HImage Level Selection StandardHigh contrast BlackboardGreenImage Level Adjustment Screen Size Adjustment Video Input Input Source Selection Video, S-VideoInput button Video Computer Video button Source Select Menu VideoInput Source Selection Component, RGB Scart 21-Pin Input button Computer Video Computer buttonVideo System Selection AutoAV System Menu Video or S-Video AV System Menu ComponentPicture level adjusted for the picture with fine tone User preset image in the Image Adjust Menu p39Cinema Image button Standard Cinema BlackboardGreen CustomTint ColorPress the Point 78 button to obtain proper color. From 0 to Progressive Resets all adjustment to their previous figureFilm Provides image at a normal video aspect ratio of 4 Provides image at a wide screen ratio of 16Setting SettingAuto setup LanguageBlue back DisplayLogo PIN code lock Enter a Logo PIN codeLogo CaptureCeiling RearStandby mode Power managementLamp mode On startRemote control PointerUSB Key lockPIN code lock To Change the PIN code lock settingTo Change the PIN code Lamp counter reset Factory defaultFan Factory default FanProjector is shut down and the Warning indicator lights red Maintenance and CleaningThen check the matters below Cleaning the Air Filters Attaching the Lens CoverCleaning the Projection Lens Cleaning the Projector CabinetLamp Replacement Reset the Lamp replace counterWhen the lamp replace counter is reset, the Lamp Lamp Replace CounterTroubleshooting AppendixRemote Control Unit does not work. Check the batteries AppendixMenu Tree Setting Image Select Image Adjust ScreenIndicators and Projector Condition Freq Compatible Computer SpecificationsKHz Technical Specifications Optional Parts LV-CA31 Not available in the U.S.AThis cable is used for RGB 21-Pin Video output of video equipmentConfigurations of Terminals USB Connector Series BTerminal HDB15-PIN Terminal DVI-IWhile the projector is locked with the PIN code Canon Communication & Image France S.A 1AA6P1P4619--MT7P