Canon LV-5220, LV-7225, LV-7220 owner manual Indicators and Projector Condition

Page 58

Appendix

Indicators and Projector Condition

Check the indicators for projector condition.

Indicators
	WARNING	LAMP	Projector Condition
POWER	WARNING	REPLACE
red/green	red	yellow
			The projector is OFF. (The AC power cord is unplugged.)
		✽	The projector is preparing for stand-by or the projection lamp is being
		✽	cooled down. The projector cannot be turned on until cooling is completed.

		✽	The projector is ready to be turned on with the POWER button.
		✽	The projector is operating normally.
		✽	The projector is in the Power management mode.
			The temperature inside the projector is abnormally high. The projector
			cannot be turned on. When the projector is cooled down enough and the
		✽	temperature returns to normal, the POWER indicator lights red and the
			projector can be turned on. (The WARNING . indicator keeps blinking.)
			Check and clean the Air filter.
			The projector has been cooled down enough and the temperature returns
		✽	to normal. When turning on the projector, the WARNING indicator stops
			blinking. Check and clean the air filters.
			The projector detects an abnormal condition and cannot be turned on.
			Unplug the AC power cord and plug it again to turn on the projector. If the
		✽	projector is turned off again, disconnect the AC power cord and contact the
			dealer or the service center for service and checkup. Do not leave the
			projector on. It may cause electric shock or a fire hazard.

• • • lights green.

• • • blinks green.

• • • lights red.

• • • blinks red.

• • • off

✽When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow, replace the projection lamp with a new one promptly. Reset the Lamp replace counter after replacement of the lamp. See page 52 and 53.

58

Image 58

Contents LV-7225LV-7220LV-5220 Blackboard can be used as a projection screen Features and DesignSee page 32 Table of Contents To the Owner Risk of Electric Shock Do not OpenSafety Instructions Hinweise für DeutschlandAir Circulation Installing the Projector in Proper PositionMoving the Projector Compliance Federal Communication Commission NoticeFront Back Bottom Part Names and FunctionsLens Cover See page 50 for attaching Rear Terminal Top Control Remote Control Unit Signal Emission indicatorLaser Pointer Function Pointer FunctionWireless Mouse Operation Operating RangeButton. The code switches sequentially for one pressing Remote Control CodeRemote Control Battery Installation With holding down the Menu button, press the ImageAdjustable Feet InstallationPositioning the Projector For the U.S.A. and Canada For Continental Europe Connecting the AC Power Cord200 240 V AC Connecting to a Computer Cables used for connectionConnecting to Video Equipment StereoConnecting to Component Video Equipment Component RGB OUTTurning On the Projector What is PIN code?Basic Operation Enter a PIN codeDisconnect the AC power cord When the projector has cooled down enough to be turned onAgain, the Power indicator lights red. Then you can Turning Off the ProjectorOn-Screen Menu How to Operate the On-Screen MenuRemote Control Unit Top ControlMenu Bar PC System MenuZoom and Focus Adjustment Auto Setup FunctionPicture Freeze Function Keystone AdjustmentNo Show Function Volume Timer FunctionSound Adjustment MuteComputer Input Input Source SelectionAuto Computer System SelectionMode PC Adjust Menu Auto PC AdjustmentTo store adjustment parameters Auto PC AdjManual PC Adjustment Display area ResetMode free Display area HHigh contrast Image Level SelectionStandard BlackboardGreenImage Level Adjustment Screen Size Adjustment Input button Video Computer Video button Video InputInput Source Selection Video, S-Video Source Select Menu VideoInput Source Selection Component, RGB Scart 21-Pin Input button Computer Video Computer buttonAV System Menu Video or S-Video Video System SelectionAuto AV System Menu ComponentCinema Picture level adjusted for the picture with fine toneUser preset image in the Image Adjust Menu p39 Image button Standard Cinema BlackboardGreen CustomTint ColorPress the Point 78 button to obtain proper color. From 0 to Progressive Resets all adjustment to their previous figureFilm Provides image at a normal video aspect ratio of 4 Provides image at a wide screen ratio of 16Auto setup SettingSetting LanguageLogo PIN code lock Blue backDisplay Enter a Logo PIN codeCeiling LogoCapture RearLamp mode Standby modePower management On startUSB Remote controlPointer Key lockPIN code lock To Change the PIN code lock settingTo Change the PIN code Fan Factory default Lamp counter resetFactory default FanProjector is shut down and the Warning indicator lights red Maintenance and CleaningThen check the matters below Cleaning the Air Filters Attaching the Lens CoverCleaning the Projection Lens Cleaning the Projector CabinetLamp Replacement Reset the Lamp replace counterWhen the lamp replace counter is reset, the Lamp Lamp Replace CounterTroubleshooting AppendixRemote Control Unit does not work. Check the batteries AppendixMenu Tree Setting Image Select Image Adjust ScreenIndicators and Projector Condition Freq Compatible Computer SpecificationsKHz Technical Specifications This cable is used for RGB 21-Pin Optional PartsLV-CA31 Not available in the U.S.A Video output of video equipmentTerminal HDB15-PIN Configurations of TerminalsUSB Connector Series B Terminal DVI-IWhile the projector is locked with the PIN code Canon Communication & Image France S.A 1AA6P1P4619--MT7P