Dukane 8915 user manual Option Menu, ONE Touch, Auto Search, Auto OFF

Page 50

Multifunctional settings

OPTION Menu

With the OPTION menu, items shown in the table below can be performed.

Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress, except for the items LAMP TIME and FILTER TIME. Then perform it referring to the following table.

 MENU [RGB]

   :SELECT

 PICTURE

 ONETOUCH

 IMAGE

 AUTO SEARCH  TURN OFF

 VIDEO Qlty.  AUTO OFF      0

 INPUT

 LAMP TIME     0

 SETUP

 FILTER TIME   0

 SCREEN

 SERVICE

 OPTION

 NETWORK

 

 EASY MENU

 

Item

Description

 

Using the buttons ▲/▼ turns on/off the automatic keystone

 

correction function.

 

 

TURN ON TURN OFF

 

 

You can automatically correct vertical keystone distortion

 

corresponding to the angle (forward/backward tilt) at which the unit

ONE TOUCH

is set up. This function works with ONE TOUCH operation.

• If the projection screen is inclined, or if the projector is angled

 

downwards, it may not be possible to make the correct adjustment

 

when V: INVERT or H&V: INVERT is selected under the MIRROR

 

item of the SETUP menu.

 

 

• When the zoom adjustment is set to the TELE side, automatic

 

correction may be excessive. The automatic correction function

 

should be used with zoom set to WIDE whenever possible.

 

 

 

Using the buttons ▲/▼ turns on/off the automatic signal search

 

function.

 

 

TURN ON TURN OFF

 

 

This function works with INPUT, RGB, and VIDEO buttons.

AUTO SEARCH

When the TURN ON is selected, detecting no signal automatically

 

cycles through input ports in order of following. The search is

 

started from the current port. Then when an input is found, the

 

projector will stop searching and display the image.

 

RGB IN1 RGB IN2 DVI-D COMPONENT VIDEO S-VIDEO VIDEO

 

 

 

Using the buttons ▲/▼ adjusts the time to count down to

 

automatically turn the projector off.

 

 

Long (max. 99 minutes) Short (min. 0 minute = DISABLE)

 

AUTO OFF

AUTO OFF

 

ENABLE

DISABLE

AUTO OFF

1

0

 

 

 

When the time is set to 0, the projector is not turned off automatically.

 

When the time is set to 1 to 99, and when the passed time with

 

a no-signal or an unsuitable signal reaches at the set time, the

 

projector lamp will go off and the power indicator begins blinking.

 

Please refer to the section “Turning off the power” (16).

38

Image 50
Contents LCD Projector Model Page About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page Trademark acknowledgment About this manualThank you for purchasing this projector Contents About contents of package Fastening the lens cap Component Part namesProjector P B P RControl buttons Remote controlLaser Indicator 14 STANDBY/ONSetting up At 169 screen ArrangementAt 43 screen Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityExamples of connection with a computer Connecting to a monitor outputConnecting to a speaker with amplifier output Component video out RGB cable RGB out LAN portLAN cable CAT-5 CB/PBConnecting power supply Putting batteries Remote controlLaser pointer Using the remote control Turning off the power Power on/offTurning on the power STANDBY/ONOperating Adjusting the volumeSelecting an input signal Temporarily muting the soundPress the ONE Touch button on the remote control. This Adjusting screen with ONE-TOUCHAdjusting the zoom and focus Selecting an aspect ratio At a RGB signal Using the automatic adjustment featureAdjusting the position  At a video signalUsing the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenUSB mouse and keyboard control Available function Remote control operationOperating the computer screen At the Easy Menu Multifunctional settingsUsing the menu function At the advanced MenuEasy Menu Mirror ResetEasy Menu Filter TimePicture Menu GammaColor Temp Picture MenuHigh  Middle  LOW  Custom SharpnessMY Memory LOAD1  LOAD2  LOAD3  LOAD4SAVE4 SAVE3  SAVE2  SAVE1 Over Scan PhaseImage Menu PositionSize Auto AdjustImage Menu Execute3D-YCS Video Qlty. MenuProgressive Video NRDVI Input MenuVideo Format Input Menu InformationStereo Setup MenuVolume IR RemoteOSD Bright Screen MenuMenu Position Bright  DarkMy Screen Screen MenuStart UP My Screen LockSync is OUT of Range MessageNo Input is Detected Auto Search Option MenuONE Touch Auto OFFOption Menu Network Menu Ex. Case of IP Address = When your network enables the Dhcp functionNetwork Menu Screen Network Menu Maintenance LampCase of replacement by yourself LampAir filter Page Related messages Internal portion temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps These has not been properly fixed Electrical power cord is not pluggedPower switch is not set to the on position Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects RGB input SpecificationDigital RGB input Video input RGB output Communication portSpecifications Page Vesa Example of computer signalVesa Text Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTDVI -D CTS Audio in Ø3.5 stereo mini jack, J K Audio INL/R RCA jackRTS DC OUTRS-232C Communication Connecting the cableCommunications setting Using the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Progressive Color Space Mute OSD Bright Dukane Corporation Audio Visual Products