Dukane 8915 user manual Regarding the indicator lamps

Page 62

Troubleshooting

Regarding the indicator lamps

Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the table below. Please respond

in accordance with the instructions within the table. If the same indication is displayed after the treatment, or if an indication other than the following is displayed, please contact your dealer or service company.

POWER

LAMP

TEMP

Description

indicator

indicator

indicator

 

 

 

 

 

Lighting

Turned

Turned

The projector is in a standby state.

In Orange

off

off

Please refer to the section “Power On/Off”.

Blinking

Turned

Turned

The projector is warming up.

In Green

off

off

Please wait.

Lighting

Turned

Turned

The projector is in an on state.

In Green

off

off

Ordinary operations may be performed.

Blinking

Turned

Turned

The projector is cooling down.

In Orange

off

off

Please wait.

 

 

 

The projector is cooling down. A certain error

Blinking

(discre-

(discre-

has been detected.

In Red

tionary)

tionary)

Please wait until the POWER indicator finishes blink,

and then perform the proper response measure using

 

 

 

 

 

 

the item descriptions below as reference.

 

 

 

The lamp does not light, and there is a

 

 

 

possibility that interior portion has become

 

 

 

heated.

 

 

 

Please turn the power off, and allow the unit to cool

Blinking

 

 

down at least 20 minutes. After the projector has

In Red

Lighting

Turned

sufficiently cooled down, please make confirmation of

or

the following items, and then turn the power on again.

In Red

off

Lighting

• Is there blockage of the air passage aperture?

 

 

In Red

 

 

• Is the air filter dirty?

 

 

 

• Does the peripheral temperature exceed 35°C?

 

 

 

If the same indication is displayed after the treatment,

 

 

 

please change the lamp by referring to the section

 

 

 

“Lamp”.

 

 

 

The lamp cover has not been properly fixed

 

 

 

(attached).

Blinking

 

 

Please turn the power off, and allow the unit to cool

 

 

down at least 45 minutes. After the projector has

In Red

 

Turned

Blinking

sufficiently cooled down, please make confirmation

or

In Red

off

of the attachment state of the lamp cover. After

Lighting

 

 

performing any needed maintenance, turn the power

In Red

 

 

 

 

on again. If the same indication is displayed after

 

 

 

 

 

 

the treatment, please contact your dealer or service

 

 

 

company.

50

Image 62
Contents LCD Projector Model Page About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page Trademark acknowledgment About this manualThank you for purchasing this projector Contents About contents of package Fastening the lens cap Component Part namesProjector P B P RControl buttons Remote controlLaser Indicator 14 STANDBY/ONSetting up At 169 screen ArrangementAt 43 screen Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityExamples of connection with a computer Connecting to a monitor outputConnecting to a speaker with amplifier output Component video out RGB cable RGB out LAN portLAN cable CAT-5 CB/PBConnecting power supply Putting batteries Remote controlLaser pointer Using the remote control Turning off the power Power on/offTurning on the power STANDBY/ONOperating Adjusting the volumeSelecting an input signal Temporarily muting the soundPress the ONE Touch button on the remote control. This Adjusting screen with ONE-TOUCHAdjusting the zoom and focus Selecting an aspect ratio At a RGB signal Using the automatic adjustment featureAdjusting the position  At a video signalUsing the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenUSB mouse and keyboard control Available function Remote control operationOperating the computer screen At the Easy Menu Multifunctional settingsUsing the menu function At the advanced MenuEasy Menu Mirror ResetEasy Menu Filter TimePicture Menu GammaColor Temp Picture MenuHigh  Middle  LOW  Custom SharpnessMY Memory LOAD1  LOAD2  LOAD3  LOAD4SAVE4 SAVE3  SAVE2  SAVE1 Over Scan PhaseImage Menu PositionSize Auto AdjustImage Menu Execute3D-YCS Video Qlty. MenuProgressive Video NRDVI Input MenuVideo Format Input Menu InformationStereo Setup MenuVolume IR RemoteOSD Bright Screen MenuMenu Position Bright  DarkMy Screen Screen MenuStart UP My Screen LockSync is OUT of Range MessageNo Input is Detected Auto Search Option MenuONE Touch Auto OFFOption Menu Network Menu Ex. Case of IP Address = When your network enables the Dhcp functionNetwork Menu Screen Network Menu Maintenance LampCase of replacement by yourself LampAir filter Page Related messages Internal portion temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps These has not been properly fixed Electrical power cord is not pluggedPower switch is not set to the on position Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects RGB input SpecificationDigital RGB input Video input RGB output Communication portSpecifications Page Vesa Example of computer signalVesa Text Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTDVI -D CTS Audio in Ø3.5 stereo mini jack, J K Audio INL/R RCA jackRTS DC OUTRS-232C Communication Connecting the cableCommunications setting Using the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Progressive Color Space Mute OSD Bright Dukane Corporation Audio Visual Products