Dukane 8915 Network Menu, When your network enables the Dhcp function, Ex. Case of IP Address =

Page 53

Multifunctional settings

NETWORK Menu (continued)

This projector provides the NETWORK function. When you start to use this function, please consult your dealer for further information.

To start, connect the LAN port to a gateway device via a CAT-5 cable, then set up the projector according to the Network environment in which you use it.

When your network enables the DHCP function

You can set automatically, if you set the DHCP function to TURN ON using the NETWORK menu. Please refer to the section NETWORK menu (40).

When your network doesn't support the DHCP function or when you use a fixed address even if your network can support the DHCP function

Please set the IP address, the subnet mask, the default gateway and the DHCP using the NETWORK menu. At ﬁrst, set the DHCP function to TURN OFF.

It is also possible to conﬁgure the projector's network settings using a Web browser (Internet Explorer 5.0 or higher; Netscape 6.2 or higher) on a computer connected to the network. When using a Web browser to conﬁgure the projector's network settings, password access is required. However, since a password is not conﬁgured when the product is shipped from the factory, if a password has not been configured, then you can simply click on Login without entering a password to access the Projector Network Conﬁguration dialog.

To conﬁgure the settings using a Web browser, proceed as follows:

ex. Case of IP Address = 192.168.1.10

1. Enter http://192.168.1.10 into the Web browser's address ﬁeld.

2. Once Screen 1 is displayed (as shown on the right), enter the password and then click on

"Login".

3. Once Screen 2 is displayed (as shown on the right), select the desired item by clicking the

corresponding ENTER button.

Information

Allows you to confirm the current network settings. (Screen 3)

IP Conﬁguration

Allows you to conﬁgure IP address, subnet mask and default gateway if DHCP is disabled. (Screen 4)

DHCP Setting

Allows you to enable or disable DHCP. (Screen 5)

Password Setting

Allows you to change the login password. (Screen 6)

Screen 1

Screen 2

41

Image 53

Contents LCD Projector Model Page About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page Trademark acknowledgment About this manualThank you for purchasing this projector Contents About contents of package Fastening the lens cap Projector Part namesComponent P B P RLaser Indicator 14 Remote controlControl buttons STANDBY/ONSetting up At 169 screen ArrangementAt 43 screen Adjusting the projectors elevator About the ﬁlter cover for bottom-up use About Plug-and-Play capability Connecting your devicesExamples of connection with a computer Connecting to a monitor outputConnecting to a speaker with ampliﬁer output LAN cable CAT-5 RGB out LAN portComponent video out RGB cable CB/PBConnecting power supply Putting batteries Remote controlLaser pointer Using the remote control Turning on the power Power on/offTurning off the power STANDBY/ONSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundAdjusting the zoom and focus Adjusting screen with ONE-TOUCHPress the ONE Touch button on the remote control. This Selecting an aspect ratioAdjusting the position Using the automatic adjustment feature At a RGB signal  At a video signalCorrecting the keystone distortions Using the magnify featureTemporarily blanking the screen Freezing the screenUSB mouse and keyboard control Available function Remote control operationOperating the computer screen Using the menu function Multifunctional settingsAt the Easy Menu At the advanced MenuEasy Menu Easy Menu ResetMirror Filter TimeGamma Picture MenuHigh  Middle  LOW  Custom Picture MenuColor Temp SharpnessMY Memory LOAD1  LOAD2  LOAD3  LOAD4SAVE4 SAVE3  SAVE2  SAVE1 Image Menu PhaseOver Scan PositionImage Menu Auto AdjustSize ExecuteProgressive Video Qlty. Menu3D-YCS Video NRDVI Input MenuVideo Format Information Input MenuVolume Setup MenuStereo IR RemoteMenu Position Screen MenuOSD Bright Bright  DarkStart UP Screen MenuMy Screen My Screen LockSync is OUT of Range MessageNo Input is Detected ONE Touch Option MenuAuto Search Auto OFFOption Menu Network Menu Ex. Case of IP Address = When your network enables the Dhcp functionNetwork Menu Screen Network Menu Lamp MaintenanceLamp Case of replacement by yourselfAir ﬁlter Page Related messages Related messages Internal portion temperature is risingRegarding the indicator lamps Regarding the indicator lamps Power switch is not set to the on position Electrical power cord is not pluggedThese has not been properly ﬁxed Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects Digital RGB input Video input SpeciﬁcationRGB input RGB output Communication portSpeciﬁcations Page Vesa Example of computer signalVesa Text Initial set signals RGB in 1, B RGB in 2, C RGB OUT Connection to the portsDVI -D RTS Audio in Ø3.5 stereo mini jack, J K Audio INL/R RCA jackCTS DC OUTRS-232C Communication Connecting the cableCommunications setting Changing the projector settings Set command Requesting projector status Get commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Progressive Color Space Mute OSD Bright Dukane Corporation Audio Visual Products