Dukane 8915 user manual Be careful in handling the light source lamp

Page 6

Safety Precautions (continued)

WARNING

Be careful in handling the light source lamp.

The projector uses a high-pressure mercury glass lamp made of glass. The lamp can break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

Please carefully read the section “Lamp”.

Be careful in handling the power cord and external connection cables. If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat, pressure or tension to the power cord and cables.

If the power cord or cables is damaged (exposed or broken core wires, etc.), contact your dealer.

Do not place the projector or heavy objects on the power cord and cables. Also, do not place a spread, cover, etc, over them because this could result in the inadvertent placing of heavy objects on the concealed power cord or cables.

Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand holding the plug or connector.

Do not place the cord near the heater.

Avoid bending the power cord sharply.

Do not attempt to work on the power cord.

Be careful in handling the battery of the remote control.

Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.

Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.

Do not allow the battery in a fire or water.

Avoid fire or high-temperature environment.

Do not hold the battery with the metallic tweezers.

Keep the battery in a dark, cool and dry play.

Do not short circuit the battery.

Do not recharge, disassemble or solder the battery.

Do not give the battery a physical impact.

Use only the battery specified in the other manual of this projector.

Make sure the plus and minus terminals are correctly aligned when loading the battery.

If you observe a leakage of the battery, wipe out the flower and then replace the battery. If the flower adheres your body or clothes, rinse well with water.

Obey the local laws on disposing the battery.

4

Image 6
Contents LCD Projector Model Page About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents About contents of package Fastening the lens cap Component Part namesProjector P B P RControl buttons Remote controlLaser Indicator 14 STANDBY/ONSetting up Arrangement At 43 screenAt 169 screen Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityConnecting to a monitor output Connecting to a speaker with amplifier outputExamples of connection with a computer Component video out RGB cable RGB out LAN portLAN cable CAT-5 CB/PBConnecting power supply Remote control Laser pointerPutting batteries Using the remote control Turning off the power Power on/offTurning on the power STANDBY/ONOperating Adjusting the volumeSelecting an input signal Temporarily muting the soundPress the ONE Touch button on the remote control. This Adjusting screen with ONE-TOUCHAdjusting the zoom and focus Selecting an aspect ratio At a RGB signal Using the automatic adjustment featureAdjusting the position  At a video signalUsing the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenAvailable function Remote control operation Operating the computer screenUSB mouse and keyboard control At the Easy Menu Multifunctional settingsUsing the menu function At the advanced MenuEasy Menu Mirror ResetEasy Menu Filter TimePicture Menu GammaColor Temp Picture MenuHigh  Middle  LOW  Custom SharpnessLOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1MY Memory Over Scan PhaseImage Menu PositionSize Auto AdjustImage Menu Execute3D-YCS Video Qlty. MenuProgressive Video NRInput Menu Video FormatDVI Input Menu InformationStereo Setup MenuVolume IR RemoteOSD Bright Screen MenuMenu Position Bright  DarkMy Screen Screen MenuStart UP My Screen LockMessage No Input is DetectedSync is OUT of Range Auto Search Option MenuONE Touch Auto OFFOption Menu Network Menu When your network enables the Dhcp function Network MenuEx. Case of IP Address = Screen Network Menu Maintenance LampCase of replacement by yourself LampAir filter Page Related messages Internal portion temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps These has not been properly fixed Electrical power cord is not pluggedPower switch is not set to the on position Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects RGB input SpecificationDigital RGB input Video input RGB output Communication portSpecifications Page Example of computer signal Vesa TextVesa Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTDVI -D CTS Audio in Ø3.5 stereo mini jack, J K Audio INL/R RCA jackRTS DC OUTConnecting the cable Communications settingRS-232C Communication Using the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Progressive Color Space Mute OSD Bright Dukane Corporation Audio Visual Products