Dukane 8915 user manual Related messages

Page 60

Troubleshooting

Troubleshooting

Related messages

When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below. If the same message is displayed after the treatment, or if a message other than the following appears, please contact your dealer or service company.

Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.

Message

Description

CHANGE THE LAMP

The time the lamp timer has counted is approaching

2000 hours.

 

AFTER REPLACING LAMP,

Preparation of a new lamp, and an early lamp change is

recommended. After you have change the lamp, please be

RESET THE LAMP TIMER.

sure to reset the lamp timer(39).

 

CHANGE THE LAMP

The time the lamp timer has counted is approaching

 

2000 hours, so a lamp change within ** hours is

AFTER REPLACING LAMP,

recommended.

RESET THE LAMP TIMER.

When lamp usage reaches 2000 hours, the power will

THE POWER WILL TURN OFF

automatically be turned off. Please change the lamp by

referring to the section “Lamp”. After you have changed the

AFTER ** hr.

lamp, please be sure to reset the lamp timer(39).

CHANGE THE LAMP

As the time the lamp timer has counted has reached

AFTER REPLACING LAMP,

2000 hours, the power will soon be automatically

turned off.

RESET THE LAMP TIMER.

Please immediately turn the power off, and change the lamp

 

THE POWER WILL TURN OFF

by referring to the section “Lamp”. After changing the lamp,

AFTER 0 hr.

please be sure to reset the lamp timer(39).

NO INPUT IS DETECTED

There is no input signal.

Please confirm the signal input connection, and the status

ON ***

of the signal source.

 

 

The horizontal or vertical wavelength of the inputted

SYNC IS OUT OF RANGE

signal is outside of the response parameters of this unit.

ON *** fH *****kHz fV *****Hz

Please confirm the specs for this unit or the signal source

 

specs.

48

Image 60
Contents LCD Projector Model Page About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents About contents of package Fastening the lens cap Part names ProjectorComponent P B P RRemote control Laser Indicator 14Control buttons STANDBY/ONSetting up Arrangement At 43 screenAt 169 screen Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityConnecting to a monitor output Connecting to a speaker with amplifier outputExamples of connection with a computer RGB out LAN port LAN cable CAT-5Component video out RGB cable CB/PBConnecting power supply Remote control Laser pointerPutting batteries Using the remote control Power on/off Turning on the powerTurning off the power STANDBY/ONAdjusting the volume Selecting an input signalOperating Temporarily muting the soundAdjusting screen with ONE-TOUCH Adjusting the zoom and focusPress the ONE Touch button on the remote control. This Selecting an aspect ratioUsing the automatic adjustment feature Adjusting the position At a RGB signal  At a video signalUsing the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenAvailable function Remote control operation Operating the computer screenUSB mouse and keyboard control Multifunctional settings Using the menu functionAt the Easy Menu At the advanced MenuEasy Menu Reset Easy MenuMirror Filter TimePicture Menu GammaPicture Menu High  Middle  LOW  CustomColor Temp SharpnessLOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1MY Memory Phase Image MenuOver Scan PositionAuto Adjust Image MenuSize ExecuteVideo Qlty. Menu Progressive3D-YCS Video NRInput Menu Video FormatDVI Input Menu InformationSetup Menu VolumeStereo IR RemoteScreen Menu Menu PositionOSD Bright Bright  DarkScreen Menu Start UPMy Screen My Screen LockMessage No Input is DetectedSync is OUT of Range Option Menu ONE TouchAuto Search Auto OFFOption Menu Network Menu When your network enables the Dhcp function Network MenuEx. Case of IP Address = Screen Network Menu Maintenance LampCase of replacement by yourself LampAir filter Page Related messages Internal portion temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Electrical power cord is not plugged Power switch is not set to the on positionThese has not been properly fixed Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects Specification Digital RGB input Video inputRGB input RGB output Communication portSpecifications Page Example of computer signal Vesa TextVesa Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTDVI -D Audio in Ø3.5 stereo mini jack, J K Audio INL/R RCA jack RTSCTS DC OUTConnecting the cable Communications settingRS-232C Communication Requesting projector status Get command Changing the projector settings Set commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Progressive Color Space Mute OSD Bright Dukane Corporation Audio Visual Products