Dukane 8915 Electrical power cord is not plugged, Power switch is not set to the on position

Page 64

Troubleshooting

Phenomena that may easily be mistaken for machine defects

WARNING ►Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer or service company.

1. Before requesting repair, please check in accordance with the following chart. This operation sometimes resolves your problem.

If the situation cannot be corrected,

2. The projector’s microprocessor may need to be reset. Please push the Restart switch by using a cocktail stick or similar and the projector will restart.

3. Some setting may be wrong. Please use the FACTORY RESET function of SERVICE menu in the OPTION menu (39) to reset all settings to factory

default.

Then, if the problem is not removed after maintenance, please contact your dealer or service company.

Phenomenon

Cases not involving a machine defect

Reference

page

Power does not

come on.

The electrical power cord is not plugged in.

13

Correctly connect the power cord.

 

The power switch is not set to the on position.

16

Set the power switch to [ ] (On).

 

The main power source has been interrupted during

 

operation such as by a power outage (blackout), etc.

 

Please turn the power off, and allow the unit to cool down at

16

least 20 minutes. After the projector has sufficiently cooled

 

down, please turn the power on again.

 

Either there is no lamp and/or lamp cover, or either

 

of these has not been properly fixed.

 

Please turn the power off, and allow the unit to cool down at

44, 45

least 45 minutes. After the projector has sufficiently cooled

 

down, please make confirmation of the attachment state of

 

the lamp and lamp cover, and then turn the power on again.

 

52

Page 63 Page 65
Image 64
Page 63 Page 65
Contents LCD Projector Model Page About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page Thank you for purchasing this projector About this manualTrademark acknowledgment Contents About contents of package Fastening the lens cap Part names ProjectorComponent P B P RRemote control Laser Indicator 14Control buttons STANDBY/ONSetting up At 43 screen ArrangementAt 169 screen Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityConnecting to a speaker with amplifier output Connecting to a monitor outputExamples of connection with a computer RGB out LAN port LAN cable CAT-5Component video out RGB cable CB/PBConnecting power supply Laser pointer Remote controlPutting batteries Using the remote control Power on/off Turning on the powerTurning off the power STANDBY/ONAdjusting the volume Selecting an input signalOperating Temporarily muting the soundAdjusting screen with ONE-TOUCH Adjusting the zoom and focusPress the ONE Touch button on the remote control. This Selecting an aspect ratioUsing the automatic adjustment feature Adjusting the position At a RGB signal  At a video signalUsing the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenOperating the computer screen Available function Remote control operationUSB mouse and keyboard control Multifunctional settings Using the menu functionAt the Easy Menu At the advanced MenuEasy Menu Reset Easy MenuMirror Filter TimePicture Menu GammaPicture Menu High  Middle  LOW  CustomColor Temp SharpnessSAVE4 SAVE3  SAVE2  SAVE1 LOAD1  LOAD2  LOAD3  LOAD4MY Memory Phase Image MenuOver Scan PositionAuto Adjust Image MenuSize ExecuteVideo Qlty. Menu Progressive3D-YCS Video NRVideo Format Input MenuDVI Input Menu InformationSetup Menu VolumeStereo IR RemoteScreen Menu Menu PositionOSD Bright Bright  DarkScreen Menu Start UPMy Screen My Screen LockNo Input is Detected MessageSync is OUT of Range Option Menu ONE TouchAuto Search Auto OFFOption Menu Network Menu Network Menu When your network enables the Dhcp functionEx. Case of IP Address = Screen Network Menu Maintenance LampCase of replacement by yourself LampAir filter Page Related messages Internal portion temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Electrical power cord is not plugged Power switch is not set to the on positionThese has not been properly fixed Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects Specification Digital RGB input Video inputRGB input RGB output Communication portSpecifications Page Vesa Text Example of computer signalVesa Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTDVI -D Audio in Ø3.5 stereo mini jack, J K Audio INL/R RCA jack RTSCTS DC OUTCommunications setting Connecting the cableRS-232C Communication Requesting projector status Get command Changing the projector settings Set commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Progressive Color Space Mute OSD Bright Dukane Corporation Audio Visual Products
Top Page Image Contents