Dukane 8915 Power on/off, Turning on the power, Turning off the power, Standby/On, Button

Page 28

1.

2.

Power on/off

Power on/off

WARNING ►When the power is on, a strong light is emitted. Do not look into the lens or vents of the projector.

NOTE • Turn the power on/off in right order. Please power on the projector before the connected devices. Power off the projector after the connected devices.

			LAMP
STANDBY/ON VIDEO RGB			TEMP
			TEMP
	UP		POWER
	PAGE
	DOWN
BLANK	LASER	STANDBY/ON	STANDBY/ON
		STANDBY/ON
		button	MENU
			INPUT
			KEYSTONE
ASPECT
			RESET
PUSH
ENTER
ESC	MENU RESET
POSITION AUTO
MAGNIFY	VOLUME
ON

FREEZE MUTE

OFF		Power switch
	KEYSTONE ONE TOUCH

Turning on the power

Make sure that the power cord is ﬁrmly and correctly connected to the projector and outlet.

Remove the lens cap, and set the power switch to the ON position.

The power indicator will light to solid orange. Then wait several seconds because buttons may not function for these several seconds.

POWER indicator

POWER (Solid orange) POWER (Blinking green)

POWER (Solid green)

3. Press the STANDBY/ON button on the projector or remote control.

The projector lamp will light up and the POWER indicator will begin blinking green. When the power is completely on, the indicator will stop blinking light green.

To display the picture, select an input signal according to the section "Selecting an input signal" (17).

Turning off the power

1. Press the STANDBY/ON button on the projector or remote control.

The message "Power off?" will appear on the screen for approximately 5 seconds.

2. Press the STANDBY/ON button on the projector or remote control again while the message is visible.

The projector lamp will go off, and the POWER indicator will begin blinking orange.

Then the POWER indicator will stop blinking and light to solid orange when the lamp cooling is complete.

Power off?

POWER (Blinking orange)

POWER (Solid orange)

3. Make sure that the power indicator lights to solid orange, set the power switch to the OFF position. The POWER indicator will go off. Attach the lens cap.

16

Image 28

Contents LCD Projector Model Page About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page Thank you for purchasing this projector About this manualTrademark acknowledgment Contents About contents of package Fastening the lens cap Part names ProjectorComponent P B P RRemote control Laser Indicator 14Control buttons STANDBY/ONSetting up At 43 screen ArrangementAt 169 screen Adjusting the projectors elevator About the ﬁlter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityConnecting to a speaker with ampliﬁer output Connecting to a monitor outputExamples of connection with a computer RGB out LAN port LAN cable CAT-5Component video out RGB cable CB/PBConnecting power supply Laser pointer Remote controlPutting batteries Using the remote control Power on/off Turning on the powerTurning off the power STANDBY/ONAdjusting the volume Selecting an input signalOperating Temporarily muting the soundAdjusting screen with ONE-TOUCH Adjusting the zoom and focusPress the ONE Touch button on the remote control. This Selecting an aspect ratioUsing the automatic adjustment feature Adjusting the position At a RGB signal  At a video signalUsing the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenOperating the computer screen Available function Remote control operationUSB mouse and keyboard control Multifunctional settings Using the menu functionAt the Easy Menu At the advanced MenuEasy Menu Reset Easy MenuMirror Filter TimePicture Menu GammaPicture Menu High  Middle  LOW  CustomColor Temp SharpnessSAVE4 SAVE3  SAVE2  SAVE1 LOAD1  LOAD2  LOAD3  LOAD4MY Memory Phase Image MenuOver Scan PositionAuto Adjust Image MenuSize ExecuteVideo Qlty. Menu Progressive3D-YCS Video NRVideo Format Input MenuDVI Input Menu InformationSetup Menu VolumeStereo IR RemoteScreen Menu Menu PositionOSD Bright Bright  DarkScreen Menu Start UPMy Screen My Screen LockNo Input is Detected MessageSync is OUT of Range Option Menu ONE TouchAuto Search Auto OFFOption Menu Network Menu Network Menu When your network enables the Dhcp functionEx. Case of IP Address = Screen Network Menu Maintenance LampCase of replacement by yourself LampAir ﬁlter Page Related messages Internal portion temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Electrical power cord is not plugged Power switch is not set to the on positionThese has not been properly ﬁxed Phenomenon Cases not involving a machine defect ReferencePhenomena that may easily be mistaken for machine defects Speciﬁcation Digital RGB input Video inputRGB input RGB output Communication portSpeciﬁcations Page Vesa Text Example of computer signalVesa Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTDVI -D Audio in Ø3.5 stereo mini jack, J K Audio INL/R RCA jack RTSCTS DC OUTCommunications setting Connecting the cableRS-232C Communication Requesting projector status Get command Changing the projector settings Set commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandCRC Be EF FB FA Color Temp Gain G Progressive Color Space Mute OSD Bright Dukane Corporation Audio Visual Products