BenQ MX511 user manual Connecting a Component Video source device

Page 22

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video output jacks available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a Component Video source device:

1.Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the Component Video output jacks of the Video source device. Match the color of the plugs to the color of the jacks; green to green, blue to blue, and red to red.

2.Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with a D-Sub type connector) to the COMPUTER 1 or COMPUTER 2 jack on the projector.

3.If you wish to make use of the projector (mixed mono) speaker(s) in your presentations, take a suitable audio cable and connect one end of the cable to the audio output jack of the device, and the other end to the AUDIO jack of the projector.

4.If you wish, you can use another suitable audio cable and connect one end of the cable to the AUDIO OUT jack of the projector, and the other end to your external speakers (not supplied).

Once connected, the audio can be controlled by the projector On-Screen Display (OSD) menus. See "Audio Settings" on page 52 for details.

The built-in speaker will be muted when the AUDIO OUT jack is connected.

•The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See "Connecting audio" on page 20 for details.

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

22 Connection

Image 22

Contents Welcome MS510/MX511 Digital ProjectorTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Projector features IntroductionShipping contents Projector exterior view Front/upper sideControls and functions ProjectorCeiling mounting the projector Remote control Up/DownTimer On Timer Setup Setting the presentation timer onPositioning your projector Choosing a locationObtaining a preferred projected image size Positioning your projector Projection dimensions Min. zoomConnection Connecting a monitor Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting audioConnecting an Hdmi source device To connect the projector to an Hdmi source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video/composite source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystoneUsing the menus Use / to highlight the System Setup Basic menuSetting a password Using a security cable lockUtilizing the password function If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Operation Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Go to the Picture Picture Mode menu Selecting a picture modeSetting the User 1/User 2 mode Optimizing the imageUsing Wall Color Fine-tuning the image quality in user modes3D Color Management About color temperaturesPress Mode/Enter and the 3D Color Management page displays Creating your own startup screen Presentation Timer Setting the presentation timerTo cancel the timer, perform the following steps Top-Left Bottom-Left Top-Right Bottom-RightRemote paging operations How to use the Timer On key?Hiding the image Freezing the image Utilizing FAQ functionTo highlight the Information menu To activate the High Altitude Mode Adjusting the soundAdjusting the sound level Operating in a high altitude environmentPersonalizing the projector menu display Shutting down the projectorMenu operation Menu systemSystem Setup Basic Setup AdvancedDescription of each menu Teaching 3D SyncInvert TemplateReference Picture ModePicture menu ModeInput signal TemperatureSave Settings Picture menu Source menuPresentation Timer Menu SettingsRemote System Setup Basic menuOperation ReceiverCooling System Setup Advanced menuQuick High AltitudeCaption Reset AllClosed StandbyInformation menu FAQ-Image InstallationFeatures Service CurrentMaintenance Care of the projectorLamp information Setting Lamp mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Projector and b lifting it off Resetting the lamp timer Tighten the screws that secure the lampIndicators Power Temp LampTroubleshooting Specifications OpticalCeiling mount screws DimensionsCeiling mount installation Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi input Supported timing for Component-YPbPrinput Warranty and Copyright information Limited warrantyRegulation statements FCC statementRegulation statements