BenQ MX511 user manual Menu operation, Menu system

Page 43

Menu operation

Menu system

Please note that the on-screen display (OSD) menus vary according to the signal type selected.

	Main menu	Sub-menu		Options

		Wall Color		Off/Light Yellow/Pink/Light
		Wall Color		Green/Blue/Blackboard
				Green/Blue/Blackboard
		Aspect Ratio		Auto/Real/4:3/16:9/16:10
		Keystone
		Position
	1.	Phase
	1.	H. Size
	DISPLAY
	DISPLAY	Digital Zoom
		3D Sync		On/Off
		3D Sync Invert		Disable/Invert
			Blackboard	Letter Formation/Musical Staff/
		Teaching	Blackboard	Worksheet/Coordinate Chart
		Teaching		Worksheet/Coordinate Chart
		Template
		Template	Whiteboard	Letter Formation/Musical Staff/
			Whiteboard	Worksheet/Coordinate Chart
				Worksheet/Coordinate Chart

		Picture Mode	Dynamic/Presentation/sRGB/Cinema/User 1/User
		Picture Mode	2
			2
		Reference Mode Dynamic/Presentation/sRGB/Cinema
		Brightness
		Contrast
		Color
	2.	Tint
	2.	Sharpness
	PICTURE
	PICTURE	Brilliant Color		On/Off
		Color		T1/T2/T3/T4
		Temperature		T1/T2/T3/T4
		Temperature
			Primary Color	R/G/B/C/M/Y
		3D Color	Hue
		Management
		Management	Saturation
			Gain
		Save Settings
	3. SOURCE	Quick Auto Search		On/Off
	3. SOURCE	Color Space Conversion		Auto/RGB/YUV
		Color Space Conversion		Auto/RGB/YUV

Operation 43

Image 43

Contents MS510/MX511 Digital Projector WelcomeTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Front/upper side Projector exterior viewProjector Controls and functionsCeiling mounting the projector Up/Down Remote controlSetting the presentation timer on Timer On Timer SetupChoosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector Min. zoom Projection dimensionsConnection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitorConnecting audio Connecting Video source devicesTo connect the projector to an Hdmi source device Connecting an Hdmi source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Correcting keystone Fine-tuning the image size and clarityUse / to highlight the System Setup Basic menu Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordChanging the password Entering the password recall procedureDisabling the password function Operation Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Optimizing the image Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Using Wall Color3D Color Management About color temperaturesPress Mode/Enter and the 3D Color Management page displays Creating your own startup screen Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Presentation TimerRemote paging operations How to use the Timer On key?Hiding the image Freezing the image Utilizing FAQ functionTo highlight the Information menu Operating in a high altitude environment Adjusting the soundAdjusting the sound level To activate the High Altitude ModeShutting down the projector Personalizing the projector menu displayMenu system Menu operationSystem Setup Basic Advanced SetupDescription of each menu Template 3D SyncInvert TeachingMode Picture ModePicture menu ReferencePicture menu Source menu TemperatureSave Settings Input signalMenu Settings Presentation TimerReceiver System Setup Basic menuOperation RemoteHigh Altitude System Setup Advanced menuQuick CoolingStandby Reset AllClosed CaptionCurrent FAQ-Image InstallationFeatures Service Information menuCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Projector and b lifting it off Tighten the screws that secure the lamp Resetting the lamp timerPower Temp Lamp IndicatorsTroubleshooting Optical SpecificationsUnit mm DimensionsCeiling mount installation Ceiling mount screwsSupported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Component-YPbPrinput Limited warranty Warranty and Copyright informationFCC statement Regulation statementsRegulation statements