BenQ MX511 user manual Operation, Starting up the projector

Page 24

Operation

Starting up the projector

1.Plug the power cord into the projector and into a

power outlet. Turn on the power outlet switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied.

Please use the original accessories (e.g. power cable) only with the device to avoid possible dangers such as electric shock and fire.

If Direct power on function is activated in the SYSTEM SETUP: Basic> Operation Settings menu, the projector will turn on automatically after the power cord has been connected and power has been applied. See "Direct power on" on page 51 for details.

2.Remove the lens cap. If it is closed, it could become deformed due to the heat produced by the projection lamp.

3.Press II Power on the projector or remote

control to start the projector. The POWER indicator light flashes and stays green when the projector is on.

The start up procedure takes about 30 seconds. In the later stage of start up, a startup logo is projected.

(If necessary) Rotate the focus ring to adjust the image clearness.

If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp.

4.If the projector is activated for the first time, select your OSD language following the on- screen instructions.

5.If you are prompted for a password, press the arrow keys to enter a six digit password. See "Utilizing the password function" on page 28 for details.

6.Switch all of the connected equipment on.

7.The projector will start to search for input signals. The current input signal being scanned displays in the screen. If the projector doesn't detect a valid signal, the message 'No Signal' will continue displaying until an input signal is found.

24 Operation

Image 24
Contents Welcome MS510/MX511 Digital ProjectorTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Projector features IntroductionShipping contents Projector exterior view Front/upper sideControls and functions ProjectorCeiling mounting the projector Remote control Up/DownTimer On Timer Setup Setting the presentation timer onPositioning your projector Choosing a locationObtaining a preferred projected image size Positioning your projector Projection dimensions Min. zoomConnection Connecting a computer or monitor Connecting a computerConnecting a monitor To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting audioConnecting an Hdmi source device To connect the projector to an Hdmi source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video/composite source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystoneUsing the menus Use / to highlight the System Setup Basic menuUsing a security cable lock Utilizing the password functionSetting a password If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Operation Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Selecting a picture mode Setting the User 1/User 2 modeGo to the Picture Picture Mode menu Optimizing the imageUsing Wall Color Fine-tuning the image quality in user modesAbout color temperatures 3D Color ManagementPress Mode/Enter and the 3D Color Management page displays Creating your own startup screen Setting the presentation timer To cancel the timer, perform the following stepsPresentation Timer Top-Left Bottom-Left Top-Right Bottom-RightHow to use the Timer On key? Remote paging operationsHiding the image Utilizing FAQ function Freezing the imageTo highlight the Information menu Adjusting the sound Adjusting the sound levelTo activate the High Altitude Mode Operating in a high altitude environmentPersonalizing the projector menu display Shutting down the projectorMenu operation Menu systemSystem Setup Basic Setup AdvancedDescription of each menu 3D Sync InvertTeaching TemplatePicture Mode Picture menuReference ModeTemperature Save SettingsInput signal Picture menu Source menuPresentation Timer Menu SettingsSystem Setup Basic menu OperationRemote ReceiverSystem Setup Advanced menu QuickCooling High AltitudeReset All ClosedCaption StandbyFAQ-Image Installation Features ServiceInformation menu CurrentMaintenance Care of the projectorSetting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Projector and b lifting it off Resetting the lamp timer Tighten the screws that secure the lampIndicators Power Temp LampTroubleshooting Specifications OpticalDimensions Ceiling mount installationCeiling mount screws Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi input Supported timing for Component-YPbPrinput Warranty and Copyright information Limited warrantyRegulation statements FCC statementRegulation statements