BenQ MX511 user manual Setup, Advanced

Page 45

		Quick Cooling		On/Off
		High Altitude Mode		On/Off
		Audio Settings	Mute	On/Off
		Audio Settings	Volume
			Lamp mode	Normal/Economic
		Lamp Settings	Reset lamp timer
			Equivalent lamp hour
	5.	Security	Change password
	SYSTEM	Security	Change Security	Power on lock
		Settings	Change Security	Power on lock
		Settings	Settings	Splash Screen on Lock
	SETUP:		Settings	Splash Screen on Lock
	SETUP:
	Advanced	Baud Rate		2400/4800/9600/14400/19200/
	Advanced	Baud Rate		38400/57600/115200
				38400/57600/115200

		Test Pattern		On/Off
			Closed Caption	On/Off
		Closed Caption	Enable	On/Off
		Closed Caption	Enable
			Caption Version
		Standby Monitor Out		On/Off
		Reset All
		Settings
		FAQ-Image and Installation
		FAQ-Features and Service
	6.
	6.			•	Source
	INFORMATI			•	Picture Mode
	ON	Current System Status		•	Resolution
	ON	Current System Status		•	Color System
				•	Color System
				•	Equivalent Lamp Hour
				•	Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

Operation 45

Image 45

Contents MS510/MX511 Digital Projector WelcomeTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Front/upper side Projector exterior viewProjector Controls and functionsCeiling mounting the projector Up/Down Remote controlSetting the presentation timer on Timer On Timer SetupChoosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector Min. zoom Projection dimensionsConnection Connecting a computer Connecting a computer or monitorConnecting a monitor To connect the projector to a notebook or desktop computerConnecting audio Connecting Video source devicesTo connect the projector to an Hdmi source device Connecting an Hdmi source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Correcting keystone Fine-tuning the image size and clarityUse / to highlight the System Setup Basic menu Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Operation Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Setting the User 1/User 2 mode Selecting a picture modeGo to the Picture Picture Mode menu Optimizing the imageFine-tuning the image quality in user modes Using Wall ColorAbout color temperatures 3D Color ManagementPress Mode/Enter and the 3D Color Management page displays Creating your own startup screen To cancel the timer, perform the following steps Setting the presentation timerPresentation Timer Top-Left Bottom-Left Top-Right Bottom-RightHow to use the Timer On key? Remote paging operationsHiding the image Utilizing FAQ function Freezing the imageTo highlight the Information menu Adjusting the sound level Adjusting the soundTo activate the High Altitude Mode Operating in a high altitude environmentShutting down the projector Personalizing the projector menu displayMenu system Menu operationSystem Setup Basic Advanced SetupDescription of each menu Invert 3D SyncTeaching TemplatePicture menu Picture ModeReference ModeSave Settings TemperatureInput signal Picture menu Source menuMenu Settings Presentation TimerOperation System Setup Basic menuRemote ReceiverQuick System Setup Advanced menuCooling High AltitudeClosed Reset AllCaption StandbyFeatures Service FAQ-Image InstallationInformation menu CurrentCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Projector and b lifting it off Tighten the screws that secure the lamp Resetting the lamp timerPower Temp Lamp IndicatorsTroubleshooting Optical SpecificationsCeiling mount installation DimensionsCeiling mount screws Unit mmSupported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Component-YPbPrinput Limited warranty Warranty and Copyright informationFCC statement Regulation statementsRegulation statements