BenQ MX511 user manual Fine-tuning the image size and clarity, Correcting keystone

Page 26

Fine-tuning the image size and clarity

1.Adjust the projected image to the size that you need using the zoom ring.

2.Then sharpen the image by rotating the focus ring.

Correcting keystone

Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen.

To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps.

Using the remote control

Press / on the projector or remote control

to display the Keystone correction page. Press

to correct keystoning at the top of the image. Press to correct keystoning at the bottom of the

image.

• Using the OSD menu

1.Press Menu/Exit and then press / until the DISPLAY menu is highlighted.

2.Press to highlight Keystone and press Mode/Enter. The Keystone correction page

 

displays.

 

 

 

 

 

 

3.

Press

to correct keystoning at the top of

Press

/ .

Press

/ .

 

the image or press

to correct keystoning

 

 

 

 

at the bottom of the image.

26 Operation

Image 26
Contents Welcome MS510/MX511 Digital ProjectorTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Projector features IntroductionShipping contents Projector exterior view Front/upper sideControls and functions ProjectorCeiling mounting the projector Remote control Up/DownTimer On Timer Setup Setting the presentation timer onPositioning your projector Choosing a locationObtaining a preferred projected image size Positioning your projector Projection dimensions Min. zoomConnection Connecting a monitor Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting audioConnecting an Hdmi source device To connect the projector to an Hdmi source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video/composite source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Correcting keystoneUsing the menus Use / to highlight the System Setup Basic menuSetting a password Using a security cable lockUtilizing the password function If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Operation Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Go to the Picture Picture Mode menu Selecting a picture modeSetting the User 1/User 2 mode Optimizing the imageUsing Wall Color Fine-tuning the image quality in user modesPress Mode/Enter and the 3D Color Management page displays About color temperatures3D Color Management Creating your own startup screen Presentation Timer Setting the presentation timerTo cancel the timer, perform the following steps Top-Left Bottom-Left Top-Right Bottom-RightHiding the image How to use the Timer On key?Remote paging operations To highlight the Information menu Utilizing FAQ functionFreezing the image To activate the High Altitude Mode Adjusting the soundAdjusting the sound level Operating in a high altitude environmentPersonalizing the projector menu display Shutting down the projectorMenu operation Menu systemSystem Setup Basic Setup AdvancedDescription of each menu Teaching 3D SyncInvert TemplateReference Picture ModePicture menu ModeInput signal TemperatureSave Settings Picture menu Source menuPresentation Timer Menu SettingsRemote System Setup Basic menuOperation ReceiverCooling System Setup Advanced menuQuick High AltitudeCaption Reset AllClosed StandbyInformation menu FAQ-Image InstallationFeatures Service CurrentMaintenance Care of the projectorLamp information Setting Lamp mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Projector and b lifting it off Resetting the lamp timer Tighten the screws that secure the lampIndicators Power Temp LampTroubleshooting Specifications OpticalCeiling mount screws DimensionsCeiling mount installation Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi input Supported timing for Component-YPbPrinput Warranty and Copyright information Limited warrantyRegulation statements FCC statementRegulation statements