BenQ MX511 user manual Resetting the lamp timer, Tighten the screws that secure the lamp

Page 60

7.Tighten the screws that secure the lamp.

Loose screw may cause a bad connection,

which could result in malfunction.

• Do not over tighten the screws.

8.Ensure the handle is fully laid flat and locked in place.

9.Replace the lamp cover by sliding it into place.

(a)

(b)

10.Tighten the screw that secures the lamp cover.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw.

11.Restart the projector.

Do not turn the power on with the lamp cover removed.

Resetting the lamp timer

12.After the startup logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP: Advanced > Lamp Settings menu. Press Mode/Enter. The Lamp Settings page

displays. Press to highlight Reset lamp timer and press Mode/Enter. A warning

message displays asking if you want to reset the lamp timer. Highlight Reset and press Mode/Enter. The lamp time will be reset to '0'.

Do not reset if the lamp is not new or replaced as this could cause damage.

60 Maintenance

Image 60
Contents Welcome MS510/MX511 Digital ProjectorTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Projector features IntroductionShipping contents Projector exterior view Front/upper sideControls and functions ProjectorCeiling mounting the projector Remote control Up/DownTimer On Timer Setup Setting the presentation timer onPositioning your projector Choosing a locationObtaining a preferred projected image size Positioning your projector Projection dimensions Min. zoomConnection Connecting a computer or monitor Connecting a computerConnecting a monitor To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting audioConnecting an Hdmi source device To connect the projector to an Hdmi source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video/composite source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystoneUsing the menus Use / to highlight the System Setup Basic menuUsing a security cable lock Utilizing the password functionSetting a password If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Operation Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Selecting a picture mode Setting the User 1/User 2 modeGo to the Picture Picture Mode menu Optimizing the imageUsing Wall Color Fine-tuning the image quality in user modesAbout color temperatures 3D Color ManagementPress Mode/Enter and the 3D Color Management page displays Creating your own startup screen Setting the presentation timer To cancel the timer, perform the following stepsPresentation Timer Top-Left Bottom-Left Top-Right Bottom-RightHow to use the Timer On key? Remote paging operationsHiding the image Utilizing FAQ function Freezing the imageTo highlight the Information menu Adjusting the sound Adjusting the sound levelTo activate the High Altitude Mode Operating in a high altitude environmentPersonalizing the projector menu display Shutting down the projectorMenu operation Menu systemSystem Setup Basic Setup AdvancedDescription of each menu 3D Sync InvertTeaching TemplatePicture Mode Picture menuReference ModeTemperature Save SettingsInput signal Picture menu Source menuPresentation Timer Menu SettingsSystem Setup Basic menu OperationRemote ReceiverSystem Setup Advanced menu QuickCooling High AltitudeReset All ClosedCaption StandbyFAQ-Image Installation Features ServiceInformation menu CurrentMaintenance Care of the projectorSetting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Projector and b lifting it off Resetting the lamp timer Tighten the screws that secure the lampIndicators Power Temp LampTroubleshooting Specifications OpticalDimensions Ceiling mount installationCeiling mount screws Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi input Supported timing for Component-YPbPrinput Warranty and Copyright information Limited warrantyRegulation statements FCC statementRegulation statements