BenQ MX511 user manual Indicators, Power Temp Lamp

Page 61

Indicators

	Light			Status & Description

	POWER	TEMP	LAMP

	Power events

	Orange	Off	Off	Stand-by mode
	Green	Off	Off	Powering up
	Flashing	Off	Off	Powering up
	Flashing
	Green	Off	Off	Normal operation
				1. The projector needs 90 seconds to cool down as it was
				abnormally shut down without the normal cooling
				down process. Or
	Orange	Off	Off	2. The projector needs to cool for 90 seconds after the
	Flashing	Off	Off	power is turned off. Or
	Flashing			power is turned off. Or
				3. The projector has shutdown automatically. If you try to
				re-start the projector, it will shutdown again. Please
				contact your dealer for assistance.

Lamp events

	Off	Off	Red	The projector has shutdown automatically. If you try to re-
	Off	Off	Red	start the projector, it will shutdown again. Please contact your
				dealer for assistance.

	Off	Off	Red	1.	The projector needs 90 seconds to cool down. Or
	Off	Off	Flashing	2.	Please contact your dealer for assistance.
			Flashing	2.	Please contact your dealer for assistance.

Thermal events

	Off	Red	Off
	Off	Flashing	Off
		Flashing

	Off	Red	Off
	Orange	Off	Off
	Flashing	Off	Off
	Flashing

The projector has shutdown automatically. If you try to re- start the projector, it will shutdown again. Please contact your dealer for assistance.

Maintenance 61

Image 61

Contents MS510/MX511 Digital Projector WelcomeTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Front/upper side Projector exterior viewProjector Controls and functionsCeiling mounting the projector Up/Down Remote controlSetting the presentation timer on Timer On Timer SetupChoosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector Min. zoom Projection dimensionsConnection Connecting a computer Connecting a computer or monitorConnecting a monitor To connect the projector to a notebook or desktop computerConnecting audio Connecting Video source devicesTo connect the projector to an Hdmi source device Connecting an Hdmi source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Correcting keystone Fine-tuning the image size and clarityUse / to highlight the System Setup Basic menu Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Operation Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Setting the User 1/User 2 mode Selecting a picture modeGo to the Picture Picture Mode menu Optimizing the imageFine-tuning the image quality in user modes Using Wall Color3D Color Management About color temperaturesPress Mode/Enter and the 3D Color Management page displays Creating your own startup screen To cancel the timer, perform the following steps Setting the presentation timerPresentation Timer Top-Left Bottom-Left Top-Right Bottom-RightRemote paging operations How to use the Timer On key?Hiding the image Freezing the image Utilizing FAQ functionTo highlight the Information menu Adjusting the sound level Adjusting the soundTo activate the High Altitude Mode Operating in a high altitude environmentShutting down the projector Personalizing the projector menu displayMenu system Menu operationSystem Setup Basic Advanced SetupDescription of each menu Invert 3D SyncTeaching TemplatePicture menu Picture ModeReference ModeSave Settings TemperatureInput signal Picture menu Source menuMenu Settings Presentation TimerOperation System Setup Basic menuRemote ReceiverQuick System Setup Advanced menuCooling High AltitudeClosed Reset AllCaption StandbyFeatures Service FAQ-Image InstallationInformation menu CurrentCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Projector and b lifting it off Tighten the screws that secure the lamp Resetting the lamp timerPower Temp Lamp IndicatorsTroubleshooting Optical SpecificationsCeiling mount installation DimensionsCeiling mount screws Unit mmSupported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Component-YPbPrinput Limited warranty Warranty and Copyright informationFCC statement Regulation statementsRegulation statements