BenQ MX511 user manual About the aspect ratio

Page 33

About the aspect ratio

In the pictures below, the black portions are inactive areas and the white portions are active areas. OSD menus can be displayed on those unused black areas.

1.

Auto: Scales an image proportionally to fit the

 

 

 

 

 

 

projector's native resolution in its horizontal or

 

 

 

 

vertical width. This is suitable for the incoming

 

 

 

 

image which is neither in 4:3 nor 16:9 and you want

16:10 picture

 

 

 

to make most use of the screen without altering the

 

 

image's aspect ratio.

 

 

 

 

 

 

 

 

 

15:9 picture

 

2.Real: The image is projected as its original resolution, and resized to fit within the display area. For input signals with lower resolutions, the projected image will display smaller than if resized to full screen. You could adjust the zoom setting or move the projector towards the screen to increase the image size if necessary. You may also need to refocus the projector after making these adjustments.

3.4:3: Scales an image so that it is displayed in the center of the screen with a 4:3 aspect ratio. This is most suitable for 4:3 images like computer monitors, standard definition TV and 4:3 aspect DVD movies, as it displays them without aspect alteration.

4.16:9: Scales an image so that it is displayed in the center of the screen with a 16:9 aspect ratio. This is most suitable for images which are already in a 16:9 aspect, like high definition TV, as it displays them without aspect alteration.

5.16:10: Scales an image so that it is displayed in the center of the screen with a 16:10 aspect ratio. This is most suitable for images which are already in a 16:10 aspect, like high definition TV, as it displays them with out aspect alteration.

4:3 picture

16:9 picture

4:3 picture

16:9 picture

16:10 picture

Operation 33

Image 33
Contents MS510/MX511 Digital Projector WelcomeTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Front/upper side Projector exterior viewProjector Controls and functionsCeiling mounting the projector Up/Down Remote controlSetting the presentation timer on Timer On Timer SetupChoosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector Min. zoom Projection dimensionsConnection Connecting a computer Connecting a computer or monitorConnecting a monitor To connect the projector to a notebook or desktop computerConnecting audio Connecting Video source devicesTo connect the projector to an Hdmi source device Connecting an Hdmi source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Correcting keystone Fine-tuning the image size and clarityUse / to highlight the System Setup Basic menu Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Operation Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Setting the User 1/User 2 mode Selecting a picture modeGo to the Picture Picture Mode menu Optimizing the imageFine-tuning the image quality in user modes Using Wall ColorAbout color temperatures 3D Color ManagementPress Mode/Enter and the 3D Color Management page displays Creating your own startup screen To cancel the timer, perform the following steps Setting the presentation timerPresentation Timer Top-Left Bottom-Left Top-Right Bottom-RightHow to use the Timer On key? Remote paging operationsHiding the image Utilizing FAQ function Freezing the imageTo highlight the Information menu Adjusting the sound level Adjusting the soundTo activate the High Altitude Mode Operating in a high altitude environmentShutting down the projector Personalizing the projector menu displayMenu system Menu operationSystem Setup Basic Advanced SetupDescription of each menu Invert 3D SyncTeaching TemplatePicture menu Picture ModeReference ModeSave Settings TemperatureInput signal Picture menu Source menuMenu Settings Presentation TimerOperation System Setup Basic menuRemote ReceiverQuick System Setup Advanced menuCooling High AltitudeClosed Reset AllCaption StandbyFeatures Service FAQ-Image InstallationInformation menu CurrentCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Projector and b lifting it off Tighten the screws that secure the lamp Resetting the lamp timerPower Temp Lamp IndicatorsTroubleshooting Optical SpecificationsCeiling mount installation DimensionsCeiling mount screws Unit mmSupported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Component-YPbPrinput Limited warranty Warranty and Copyright informationFCC statement Regulation statementsRegulation statements